Burner Locations - LP WGC Série Mode D'emploi

4. Test the gas pressure regulator and gas supply line.
The regulator must be checked at a minimum 1" (2.5 cm)
water column above the set pressure. The inlet pressure to
the regulator should be as follows for operation and checking
the regulator setting:
LP Gas:
Minimum pressure 10" (25.4 cm) W.C.P.
Supply pressure 14" (35.5 cm) W.C.P.
Gas Supply Pressure Testing
Line pressure testing above ½ psi gauge (14" WCP)
The cooktop and its individual shutoff valve must be
disconnected from the gas supply piping system during any
pressure testing of that system at test pressures in excess of
½ psi (3.5 kPa).
Line pressure testing at ½ psi gauge (14" WCP) or lower
The cooktop must be isolated from the gas supply piping
system by closing its individual manual shutoff valve during
any pressure testing of the gas supply piping system at test
pressures equal to or less than ½ psi (3.5 kPa).
5. If the burner grates are installed, remove them.
Use the following charts to match the correct gas orifice spud
with the burner location and model being converted.
LP Gas Orifice Spud Chart for Kit W10676661
Burner Color
Rating
5,000 BTU Green
7,000 BTU White
8,000 BTU Orange
11,000 BTU Red
13,000 BTU Yellow
16,000 BTU Pink
12,000 BTU
Inner Brown
Outer Brown
Burner Models for Kit W10676661
Model No. Left Left
Front Rear
WCG51US0D 66 108
MGC7430D Green Yellow
ICS500DS00
WCG75US0D 66 115
MGC9530D Green Pink
WCG97US0D 75 79
KCGS350E White Orange
ICS655DS00
WCG51US6D 75 75
MGC7536D White White
WCG97US6D 75 75
MGC9536D White White
KCGS356E
4
Stamp Size
(A)
66 0.66 mm
75 0.75 mm
79 0.79 mm
97 0.97 mm
108 1.08 mm
115 1.15 mm
85 0.85 mm
48 0.48 mm
A. Size stamp
Center Center Right Right
Inner Outer Rear Front
Inner
N/A N/A 97
Red White
N/A N/A 97
Red White
85 48 66
Brown Brown Green White
108 108 66
Yellow Yellow Green Red
85 48 66
Brown Brown Green Red
LP Gas Orifice Spud Chart for Kit W10676662
Burner
Rating
5,000 BTU
6,000 BTU
9,100 BTU
11,000 BTU
13,000 BTU
Inner
Outer
14,000 BTU
Inner
Outer
16,000 BTU
Inner
Outer
9,000 BTU
Inner
Outer
Burner Models for Kit W10676662
Model No.
KCGS550E
KCGS556E
KCGS950ES
KCGS956ES
A

Burner locations

Right
Front
Outer
75 75
A
White
75 75
White
75 75
White
6. Remove all burner caps and burner bases (see the User
97 97
Red Guide for burner reference).
To remove the burner base for the Dual Flame and Dual Tier
97 97
Ultra Torch burners use a Torx
Red
Color Stamp Size
(A)
White 66 0.66 mm
Green 70 0.70 mm
Black 89 0.89 mm
Orange 97 0.97 mm
Blue 45 0.45 mm
Brown 97 0.97 mm
Blue 45 0.45 mm
Yellow 101 1.01 mm
Blue 45 0.45 mm
Red 105 1.05 mm
Pink 40 0.40 mm
Pink 80 0.80 mm
Left Left Center Center
Front Rear Inner Outer
66 89 97 45
White Black Brown Blue
66 89 101 45
White Black Yellow Blue
66 89 97 45
White Black Brown Blue
66 97 105 45
White Orange Red Blue
B C
A. Left front D. Right rear
B. Left rear E. Right front
C. Center
® T10 driver to remove the screw.
A
A. Size stamp
Right Right Right
Rear Front Front
Inner Outer
70 89 89
Green Black Black
70 89 89
Green Black Black
70 80 40
Green Pink Pink
70 80 40
Green Pink Pink
D
E