Bestell-Information Pumpenköpfe / Ordering information pump-heads / Information de commande têtes de pompes
Kopf
Max.
Fließraten ml/min
Head / Tête
Temp.
Flow rates/Débit Differential pressure/Pression différentielle
120
1
)
99°C
a
)
33– 3290
121
1
)
99°C
a
)
33–3290
130
1
)
122°C
a
)
33–3290
140
1
)
99°C
a
)
33–3290
1
a
141
)
99°C
)
33–3290
1
a
150
)
122°C
)
33–3200
2
180
)
177°C
2– 210
1
181
)
177°C
2– 210
182
2
)
177°C
4– 420
183
1
)
177°C
4– 420
186
1
)
177°C
1–
82
188
2
)
177°C
1–
82
1800
2
)
177°C
5– 466
1830
1
)
177°C
5– 466
Magnet/aimant:
1
) MI 0066
2
) IS 1598
Die Pumpenköpfe sind für einen Systemdruck von max.
20 bar ausgelegt. Das Gehäusematerial ist aus Edelstahl
SS 316/DIN 1.4571.
Pumpenköpfe mit gleichem Magnet sind untereinander
auswechselbar.
a
Für Temperaturen über 54°C (130°F) wenden Sie sich für
)
die richtige Wahl des Dichtungsmaterials an Ihre
ISMATEC-Vertretung. (Betriebstemperatur angeben).
b
)
Der Bypass sollte vor allem aus Sicherheitsgründen und
nicht zur Druckregelung verwendet werden.
ISMATEC SA/REGLO-Z/-ZS/24.04.02/CB/GB
Differenzdruck max. bar
mit/with/avec
Bypass
2.0
b
)
2.0
b
)
2.0
b
)
2.0
2.0
2.0
2.8
2.8
2.8
2.8
1.4
1.4
3.0
5.2
Adapter: AR 0001
The pump-heads are designed for a system pressure of
max. 20 bar. The housing is stainless steel SS 316/DIN
1.4571.
Pump-heads using the same magnets are interchangeable.
a
) For temperatures above 54°C (130°F) consult your
ISMATEC distributor for proper seal selection.
(Indicate your operation temperature).
b
)
The bypass should only be used fore safety reasons and
not for pressure control.
Material /Matériaux
Material/Matériaux
Zahnrad/Gear/Engrenage
Dichtungen/Seals/Etanchéités
PTFE
PTFE
PTFE
PTFE
PPS
PTFE
PTFE
PTFE
PTFE
PTFE
PPS
PTFE
Graphite
PTFE
Graphite
PTFE
Graphite
PTFE
Graphite
PTFE
Graphite
PTFE
Graphite
PTFE
PPS
PTFE
PPS
PTFE
PPS = Polyphenylenesulphide
PTFE = Polytetrafluorethylene
Les têtes de pompe ont été développées pour des pressions
d'exploitation maximales de 20 bars. Le matériau du boîtier
est constitué d'acier surfin SS 316/DIN 1.4571. Les têtes de
pompe équipées d'un même aimant sont échangeables.
a
) Si vous travaillez à des températures dépassant les 54°C
(130°F), renseignez-vous auprès de votre représentant
ISMATEC quant au choix optimal du matériau
d'étanchéité.
b
) Le conduit de dérivation (bypass) ne doit être utilisé
uniquement pour des raisons de sécurité, non pour le
contrôle de la pression.
Order No.
No. de comm.
a
)
MI 0013
a
)
MI 0014
a
)
MI 0019
a
)
MI 0016
a
)
MI 0017
a
)
MI 0020
MI 0010
MI 0007
MI 0011
MI 0008
MI 0006
MI 0009
MI 0187
MI 0131
21