Seg Cordoba Mode D'emploi page 46

■ LNB TYPE: Select the LNB type.
■ LNB Power : Select the power supply type for the LNB.
22KHz 22KHz SWITCH. Select the 22KHz depending on
■ :
the LNB type.
Toneburst You can choose one of two satellites. Used to
■ :
choose proper device.
DiSEqC1.0
■ : You can choose one of four satellites. Used to
choose proper device.
■ Motor : Sets the positioned type between DiSEqC1.2 and
USALS.
When Motor is set to DiSEqC1.2 or USALS:
- Set Position : Press the ENTER button to set Position.
Move Auto: Rotates the antenna automatically.
Move Continue: Rotates the antenna until the rotation has
been completed or stopped manually.
Move Step: Rotates the antenna in accordance with the step
value. Enables the antenna make a finer adjustment.
Goto Position: Rotates the antenna to the stored satellite
position.
Goto Reference: Drive antenna to zero position.
GotoX: Moves the antenna to the location specified by Set
Location.
Store Position: Stores current position as the selected posi-
tioner limit.
- Set Limit
: Press the red button to set Limits to the scope of
satellite antenna rotation.
Move Continue: Rotates the antenna until the rotation has
been completed or stopped manually.
Move Step. Rotates the antenna in accordance with the
step value. Enables the antenna make a fine adjustment.
Set West Limit. Set the west limit value.
Set East Limit. Set the east limit value.
Goto Reference. Drive antenna to zero position.
Disable Limit. Delete Limit settings. Allows the antenna to
rotate over the full arc. Cancel east limit and west limit.
When Motor is set to USALS:
-Set Location Press the green button to set Location.
:
Location. Selects the Set Location mode.
Longitude Direction, Longitude Angle, Latitude Direction,
Latitude Angle can be adjusted when the Location is set to
Manual.
Longitude Direction: Sets the longitude direction for the
location.
Longitude Angle: Sets the longitude angle for the location.
Latitude Direction: Sets the latitude direction for the loca-
tion.
Latitude Angle. Sets the latitude angle for the location.
4
Cordoba 66cm LED BLU-TV
■ Reset All: Satellite list, transponder list and some set-
tings will be reset to the default values. After reset all,
you can reset the country while Auto Tuning.
Quality: Display the current status of broadcasting signal.
■
Scan Press the blue button to enter the Channel Tuning
■ :
menu.
Scan mode: Selects the scanning mode of the selected
satellite.
Encrypted: Scan either free or all channels.
Service Type: Select the channel type to memorise.
When setting is completed, press the ENTER button.
Channel Tuning is started.
• Programme Edit
▲/▼
Press the button select items.
Press the red button to delete the channel.
Press the green button to rename the channel. (In TV mode)
Press the yellow button to move the channel. (Except DTV
channels with LCN) - not supported in Germany.
Press the blue button to skip the channel.
Press the button to set the favorite channel.
The CH+/CH- button can be used to select the following or
preceding page.
• Channel List Transfer
You can export all current channel information (including
channel number, channel name, frequency, etc.) into the
U disk, as the channel information backup for this unit.
The system will automatically create a data file to store
the channel information has been exported.
If you can not restore the initial channel information after
SORT, MOVE, DEL, SKIP, LOCK, etc. operations, you can
import the channel information from the USB.
• CI Information (In DTV mode)
- USING YOUR COMMON INTERFACE SLOT
This TV set features a CI+ slot and supports the following
digital standards: DVB-T, DVB-S(S2) and DVB-C.
- Common Interface
The Common Interface (CI+) slot is designed to accept
the Conditional Access Module (CAM) and Smart Card
in order to view the pay TV programmes and additional
services. Contact your Pay Per View TV service provider
to get more information about the modules and subscrip-
tions.
NOTE:
Conditional Access Module and Smart Cards are sold
separately.