GreenWorks Tools 3802507 Manuel D'utilisation page 4

EN
DE ES IT FR PT NL RU FI SV NO DA PL CS SK SL HR HU RO BG EL AR TR HE LT LV ET
To prevent gear damage, always allow the chuck
to come to a complete stop before changing the
direction of rotation.
To stop the drill, release the switch trigger and allow
the chuck to come to a complete stop.
NOTE: The drill will not run unless the direction of rotation
selector is pushed fully to the left or right.
Avoid running the drill at low speeds for extended periods
of time. Running at low speeds under constant usage
may cause the drill to become overheated. If this occurs,
cool the drill by running it without a load and at full speed.
Using The Auxiliary Handle Assembly (see
figure E)
■ Loosen the handle assembly by turning the handle
counterclockwise.
■ Slide the auxiliary handle assembly onto the hammer
drill in the desired operating position either right
handed or left handed.
■ Securely tighten by turning the auxiliary handle
clockwise.
NOTE
: Be sure the auxiliary handle is securely tightened
against the depth stop rod clamp. This secures the depth
stop rod at the desired depth of cut. It also secures the
auxiliary handle.
Adjusting The Depth Stop Rod (see figure F - G)
■ Lock the switch trigger by placing the direction of
rotation selector in the center position.
■ Press the rod adjustment button.
■ Adjust the depth stop rod so that the drill bit extends
beyond the end of the rod to the required drilling depth.
■ Relese the rod adjustment button.
NOTE
: When properly installed, the teeth on the depth
stop rod should be aligned with the teeth indicator on the
depth stop rod clamp.
Fitting And Changing SDS Bit (see figure H)
This tool is equipped with an SDS Plus connection
system.
■ Clean the bit and grease it with machine grease before
inserting it into the chuck.
■ Pull back the clamp collar and hold it.
■ Push and rotate the dust-free tool into the bit holder as
far as it will go.
■ Release the clamp collar to lock the bit.
■ Check that bit has locked by pulling on it.
Removing The Bit From The SDS Plus System
(see figure I)
■ Pull back the clamp collar and remove the bit.
English (Original Instructions)
Mode Selector(see figure J)
In general, rotary mode should be used for drilling and
other heavy duty applications. Hammer mode should be
used for hammer drilling.
To change the operating mode, push the release button
and turn the mode selector switch to the requested
position until it can be heard to latch.
■ For drilling, place the selector in the ( ) position.
■ For hammer drilling, set mode selector to (
Switch between modes when tool is at a standstill.
NOTE
: Hammer drilling mode will damage the tool's
mechanism when used for fastening or drilling by non-
SDS Plus bits. Select the rotary mode only on such
purpose.
When hammer drilling, use only bits with hard metal and
SDS Plus shaft only. The use of commercially available
masonry bits with cylindrical shaft by means of the drill
adaptor is impossible.
When hammer drilling, do not apply too much
pressure. Too much pressure will place unnecessary
load on the motor.
Drilling (see figure K)
■ Check the direction of rotation selector for the correct
setting (forward or reverse).
■ Secure the material to be drilled in a vise or with
clamps to keep it from turning as the drill bit rotates.
■ Hold the drill firmly and place the bit at the point to be
drilled.
■ Depress the switch trigger to start the drill.
■ Move the drill bit into the workpiece, applying only
enough pressure to keep the bit cutting. Do not force
the drill or apply side pressure to elongate a hole. Let
the tool do the work.
Be prepared for binding at bit breakthrough. When
these situations occur, drill has a tendency to grab
and kick opposite to the direction of rotation and
could cause loss of control when breaking through
material. If not prepared, this loss of control can result
in possible serious injury.
■ When drilling hard, smooth surfaces, use a center
punch to mark the desired hole location. This will
prevent the drill bit from slipping off-center as the hole
is started.
■ When drilling metals, use a light oil on the drill bit to
keep it from overheating. The oil will prolong the life of
the bit and increase the drilling action.
■ If the bit jams in the workpiece or if the drill stalls,
stop the tool immediately. Remove the bit from the
workpiece and determine the reason for jamming.
NOTE
: This drill has an electric brake. When the switch
4
CAUTION
WARNING
).