Toshiba Carrier RAS-09LKV-UL Série Mode D'emploi page 3

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

1
SYSTEM CHARACTERISTICS
1. Three-minute time delay: To protect against frequent compressor starts.
2. Preheating operation: Warm up the unit for several minutes before
blowing warm air.
3. Warm air control: When the room temperature reaches the set
temperature, the fan speed is automatically reduced and the outdoor unit
will stop.
4. Automatic defrosting: Fans will stop during defrost operation.
5. Heating capacity: Heat is absorbed from outdoor and released into
the room. When the outdoor temperature is too low, use another
recommended heating apparatus in combination with the air conditioner.
6. Some minor cracking sound may occur when unit operating. This is
normal and is caused by expansion/contraction of plastic.
Note: Item 2 to 5 for Heating model
Air conditioner operating conditions
Temp.
Outdoor Temperature
Operation
Heating
5°F ~ 75°F (–15°C ~ 24°C)
Cooling
14°F ~ 115°F (–10°C ~ 46°C)
Dry
14°F ~ 115°F (–10°C ~ 46°C)
2
INDOOR UNIT DISPLAY
3
PREPARATION BEFORE USE
Preparing Filters
1. Open the air inlet grille and remove the air fi lters.
2. Attach the fi lters. (see detail in the accessory sheet).
Loading Batteries
1. Remove the battery cover.
2. Insert 2 new batteries (AAA type)
following the (+) and (–) positions.
Clock Setup
1. Push CLOCK
by tip of the pencil.
If timer indication is fl ashing, go to the next step 2.
ON
OFF
2. Press
or
: adjust the time.
3. Press
SET
: Set the time.
Temperature Unit °F-°C Selection
1. Push and hold CHK
button on the Remote
Control by the tip of the pencil, "00" will be
shown on the display.
2. Press
while pushing CHK
SLEEP
Note: 1. Repeat above step to reset Remote
Control to be °F.
2. Operation mode and temperature
set will reset to initial setting after
change the temperature unit.
3. Default setting of Remote Control
from factory is °F.
4
REMOTE CONTROL A-B SELECTION
To separate using of remote control for each indoor unit in case of 2 air
conditioners are installed adjacent to each other.
Remote Control B Setup.
1. Press RESET button on the indoor unit to turn the air conditioner ON.
2. Point the remote control at the indoor unit.
3. Push and hold CHK
button on the Remote Control by the tip of the
pencil. "00" will be shown on the display.
MODE
4. Press
while pushing CHK
will disappear and the air conditioner will turn OFF. The Remote Control
B is memorized.
Note: 1. Repeat above step to reset Remote Control back to A.
2. Remote Control A have not "A" display.
3. Default setting of Remote Control from
factory is A.
1110650133-1-EN.indd 3
1110650133-1-EN.indd 3
Room
Temperature
Less than 82°F (28°C)
70°F ~ 90°F (21°C ~ 32°C)
62°F ~ 90°F (17°C ~ 32°C)
1 Hi POWER (Green)
2 FILTER (Orange)
3 PRE. DEF (Preheat/Defrost)
(Orange)
4 TIMER (Yellow)
5 OPERATION (Green)
6 RESET button
.
CLR
SLEEP
SET
. "B" will show on the display and "00"
"B" Display
"00" Display
5
AIR FLOW DIRECTION
FIX
1
Press
: Move the louver to the
desired vertical direction.
SWING
Press
: To continuously swing
2
the louver automatically and press
again to stop.
For horizontal direction, adjust
3
manually.
Note:
• Do not move the louver manually by others.
• The louver may automation positioning by some operation mode.
6
REMOTE CONTROL
1 Infrared signal emitter
2 Start/Stop button
3 Mode select button (MODE)
4 Temperature button (TEMP)
5 Fan speed button (FAN)
6 Swing louver button
(SWING)
7 Set louver button (FIX)
8 On timer button (ON)
9 Off timer button (OFF)
! Sleep timer button (SLEEP)
" Setup button (SET)
# Clear button (CLR)
$ Memory and Preset button
(PRESET)
% One-Touch button
(ONE-TOUCH)
& High power button
(Hi-POWER)
( Economy button (ECO)
) Quiet button (QUIET)
~ Comfort sleep button
(COMFORT SLEEP)
+ Filter reset button (FILTER)
, Clock Reset button (CLOCK)
- Check button (CHK)
7
ONE-TOUCH
Press the "ONE-TOUCH" button for fully automated operation that is
customized to the typical consumer preferences in your region of the world.
The customized settings control temperature air fl ow strength, air fl ow
direction and other settings to provide you alternate contact with "ONE-
TOUCH" of the button. If you prefer other settings you can select from the
many other operating functions of your unit.
ONE-TOUCH
Press
: Start the operation.
8
AUTOMATIC OPERATION
To automatically select cooling, heating, or fan only operation
MODE
1. Press
: Select A.
2. Press
TEMP
: Set the desired temperature.
EN
ES
FR
PRESET
FAN
TEMP
ONE-TOUCH
MODE
COMFORT
QUIET
SLEEP
SWING
FIX
Hi-POWER ECO
TIMER
CLR
ON
OFF
SLEEP
SET
˚C/˚F
CHK
FILTER
CLOCK
1/4/10 3:50:57 PM
1/4/10 3:50:57 PM

Publicité

Table des Matières
loading

Table des Matières