Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
0702 653 X.book Seite 13 Dienstag, 19. Oktober 2010 10:53 10
Maintenance and Cleaning
Before any work on the machine itself, pull the
mains plug.
For safe and proper working, always keep the
machine and the ventilation slots clean.
The power tool must be serviced by a Würth master
Service after 150 operating hours.
Service Indication
The yellow LED lights up when the carbon brushes
are almost completely worn. After approx. 8 further
operating hours, the brushes will be completely
worn and the motor will shut off automatically.
The red LED lights up when the lock-on button is used
in a different operating mode than chiselling. The
red LED starts to flash when a power tool malfunc-
tion is given, or when the brushes are completely
worn.
If the machine should fail despite the care taken in
manufacturing and testing, repair should be carried
out by a Würth Master-Service agent.
For all correspondence and spare parts orders,
always include the article number on the type plate
of the machine.
For the current spare parts list of this machine, log
into the Internet under
"http://www.wuerth.com/partsmanager" or ask
for a copy at your nearest Würth branch office.
Disposal
Power tools, accessories and packaging should be
sorted for environmental-friendly recycling.
Only for EC countries:
Do not dispose of power tools into
household waste!
According to the European Directive
2002/96/EC on waste electrical
and electronic equipment and its
incorporation into national law, power tools that are
no longer suitable for use must be separately col-
lected and sent for recovery in an environmen-
tal-friendly manner.
Warranty
For this Würth tool, we provide a warranty in
accordance with statutory /country-specific regula-
tions from the date of purchase (proof of purchase
by invoice or delivery note). Damage that has
occurred will be corrected by replacement or repair.
Damage caused by normal wear, overloading or
improper handling is excluded from the warranty.
Claims can be accepted only when the machine is
presented undisassembled to a Würth branch office,
your Würth sales representative or a customer serv-
ice agent for Würth pessure air and power tools.
Noise/Vibration Information
Measured
values
determined
2000/14/EG.
BMH 40-XES MH 5-XES
L
(
sound pressure
PA
level
93 dB (A)
)
sound pressure level
K
(
-
PA
3 dB (A)
Measuring inaccuracy)
sound power level
104 dB (A)
L
(
)
WA
sound power level
K
(
-
WA
3 dB (A)
Measuring inaccuracy)
Wear hearing protection!
Overall vibrational value (vector sum of three direc-
tions) determined according to EN 60 745:
BMH 40-XES MH 5-XES
Hammer drilling in
concrete
Vibrational emission
value
a
9.1 m/s
h
uncertainty
K
1.6 m/s
Chiselling
Vibrational emission
value
a
7.4 m/s
h
uncertainty
K
1.6 m/s
The vibration emission level given in this information
sheet has been measured in accordance with a
standardised test given in EN 60745 and may be
used to compare one tool with another. It may be
used for a preliminary assessment of the vibrational
impact.
The declared vibration emission level represents the
main applications of the power tool. However if the
power tool is used for other applications, with differ-
ent accessories or poorly maintained, the vibration
emission may differ. This may significantly increase
the vibrational impact over the total working period.
An estimation of the level of exposure to vibration
should also take into account the times when the tool
is switched off or when it is running but not actually
doing the job. This may significantly reduce the
exposure level over the total working period.
according
to
95 dB (A)
3 dB (A)
106 dB (A)
3.6 dB (A)
2
–
2
–
2
2
8.3 m/s
2
2
1.5 m/s
13
Publicité
Table des Matières
