Before First Use - Hotpoint Ariston SL D10 BAW Mode D'emploi

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 23

BEFORE FIRST USE

Remove all adhesives, protective plastic materials
and cardboard packaging. Make sure all adhesive
parts are removed with a soft damp cloth.
Assembling
1.
Fasten the plastic flexible hose (11) to the suction
inlet (16) until it clicks into place. To remove it,
press the release (17) and pull it out.
2.
Fit the metal extension pipe (9) into the hand
grip (10) until it locks into place. Use the length
regulator (8) to adjust the length of the pipe.
3.
Fit the attachment you need (see chapter
"Attachments") into the end of the metal
extension pipe until it locks into place.
If your appliance is equipped with a Remote
Power Control, you will need to insert the
batteries supplied (see paragraph "Remote Power
Control" under chapter "Features").
USING
THE VACUUM CLEANER (A)
The appliance is equipped with a safety
device that prevents the dust-compartment
lid from closing unless the dust bag has been
correctly installed. Do not force the dust bag lid to
close and make sure all the parts are in the correct
position to allow you to close the lid.
Do not use the vacuum cleaner without
filters, Pure Clean dust bag, dust bag support
or dust container, as the appliance could get
damaged.
1.
Unwind the power cord (34) and plug the
appliance into an electrical outlet (220/240V).
We advise you to unwind the entire power
cord (yellow marker: 6,5m; red marker: 7m)
to avoid any overheating and damage.
2.
Press the start/stop button (19) to start the
appliance.
3.
Press the Trolley System opening/closing
button (13) to extend the carrying handle (12)
to the desired length until it locks into place.
Then manoeuvre the vacuum cleaner using the
carrying handle when cleaning the house.
4.
To select the desired suction intensity
(based on the model) use the +/- button
and electronically adjust the power (21) of
the Remote Power Control; or manually
rotate the electronic power regulator (26).
We advise you to use a low suction power
on delicate surfaces such as curtains,
fabrics, cushions etc to avoid any damage; or at
least open the air regulator to reduce the suction
effect.
5.
To pause the vacuum cleaner, if this feature is
available, you can use the standby button (22)
on the Remote Power Control or the Start & Stop
function (based on the model). Just insert the
brush into its horizontal housing (30).
6.
To switch off the appliance press the start/stop
button again.
7.
Disconnect the plug from the electrical
outlet
and
button (20) until rewinding is complete.
Make sure the cord does not get entangled
during rewinding.
8.
Secure the floor head into its horizontal / vertical
housing and store the appliance.
Do not start the vacuum cleaner if the plastic
flexible hose is entangled, as this could
damage the appliance.
FEATURES
Electronic power regulator (B)
The electronic power regulator (26) (if available) al-
lows to set the suction power required.
On some models, the ideal power levels are indica-
ted, according to the surface to be cleaned: awnings,
carpets and hard floors.
The Eco function (if available) allows to save 25%
energy, compared with the consumption relative to
max suction power, ensuring at the same time clea-
ning efficacy.
Remote Power Control (C)
The Remote power control (if available) enables you
to adjust the suction power directly and effortlessly
from the hand grip, with no need to bend. When using
the vacuum cleaner, you can keep it on standby by
pressing the Start & Pause button (22).
To insert or change the batteries of your Remote
Power Control:
1.
Open the battery compartment (23).
2.
Insert two AAA batteries, making sure of the
positive and negative poles.
3.
Close the battery compartment until it clicks into
place.
press
the
cord-rewind
it en
17

Publicité

Table des Matières
loading

Table des Matières