Publicité
Les langues disponibles
Les langues disponibles
en
Instruction
ADM-I12W1 motion detector
The detector detects movement in the
room under surveillance
an alarm. It responds most sensitively to
movement in the directions indicated by
arrows
B / D. The alarm is transferred
by wireless. The back tamper recognizes
if the detector is removed with force.
Prerequisites
The detector should be installed by peo-
ple with specialist knowledge and in com-
pliance with valid regulations.
The detector is only intended
for indoor use. Note the posi-
tioning instructions
Opening the detector
1. Check the scope of delivery
2. Slide up the screw-on cover
loosen the screw
B.
3. Pull the housing front
2
C.
Fitting the detector
1. Fit the mounting base
- Define type of fastening
refer to mounting bracket option)
- Break open three fixing holes.
- Fit mounting base at the proposed
height.
The mounting base should be
secured using two screws
A / B and the back tamper
with one screw
2. Pull out insulation strip between bat-
tery and bracket
A.
3. Press the tamper contact
ter the detector with the system.
For safety reasons only use
the battery supplied and not
any other type.
4. Fold front
D back onto mounting
base
2
C and secure with screw
Slide down screw-on cover
Programming
To adjust the settings to the application,
move the switches
A into the corre-
sponding positions:
Switch
Function
1
LED
2
Sensitivity
3
Auto Power Save
4
Pet Immunity
* Factory Setting
Sensitivity setting
and initiates
* factory setting is the middle position
(12-meter field of vision)
Potentiometer settings other than the
centre (factory) position are not certi-
fied by Telefication for EN compliance
and will result in a different coverage
area.
ID registration
You will find instructions for integrating
the detector in the control panel in the
.
control panel's installation manual.
Walk test
.
1. Call up walk test mode in the control
A and
panel.
2. Hold a magnet to the right of the de-
D off the base
tector for 1 second
3. Run the walk test for alarm triggering
in the whole detection area
C as follows:
detector.
4
A / B. (also
Alarm transmission test
1. Call up walk test mode in the control
panel.
2. Hold a magnet to the right of the detec-
tor for at least 2 seconds
3. The alarm transmission test has now
started. 11 test signals are sent to the
control panel at an interval of 6 sec-
C.
onds (the LED
transmission).
4. The test is passed if the control panel
receives the test signals and indicates
5
B to regis-
this accordingly.
Options
Narrow angle lens kit AO-C25
The kit enables the detection area cover-
age to be defined to a narrow angle as
shown in
Loosen the lens currently at the positions
2
B.
shown in
A.
tor. Insert adapter
press down narrow angle lens.
White light filter AO-WL10k*
The white light filter is needed for applica-
tions with extreme white light interference
(> 4000 lux).
ON
OFF
Loosen the lens currently at position
*On
Off
and remove this from the detector. Insert
*Low
High
adapter
lens back down.
*On
Off
* Note: Not certified by Telefication for
25kg
*15kg
EN compliance.
Wall & ceiling mounting brackets
The mounting brackets AZ-MBG2
9
(ceiling
be used to swivel the detector ±45°.
D
Turn potentiometer
D
into the position required to
adjust detector to room size
and field of vision.
B.
7
of the
B.
10
flashes during each
D.
F and remove from the detec-
C in to detector and
B in to detector and press the
B and wall
C mounting) can
Technical data
Detection area cov-
erage
wide angle
B
Detection area cov-
erage
narrow angle
D
Range of wireless
module
Frequency:
ADM-I12W1
Identification
Data protocol
Event transmission
Test mode
Battery power sav-
ing
Battery
Warm up period
Pet immunity
EMI rejection up to
2 GHz
Operating tempera-
ture
Storage tempera-
ture
Air humidity
EN 60721
Type of housing
protection
EN 60529,
EN 50102
EC Declaration of Conformity
Hereby, Vanderbilt International (IRL) Ltd
declares that this radio equipment type is
in compliance with all relevant EU Direc-
tives for CE marking. From 20/04/2016 it
is in compliance with Directive
2014/30/EU (Electromagnetic Compatibil-
ity Directive) and Directive 2014/35/EU
(Low Voltage Directive). From 13/06/2016
it is also in compliance with Directive
F
2014/53/EU (Radio Equipment Directive).
The full text of the EU declaration of con-
formity is available at:
http://pcd.vanderbiltindus-
tries.com/doc/wireless
9
9
A
12 m
20 m
Up to 300 m out-
doors
868 MHz
ID serial number
24 bits
SiWay
Alarm, sabotage,
surveillance, bat-
tery low
Walk test & alarm
transmission test
Automatic energy
saving function
Lithium 3 V
Type: xx123
Size: 2/3 AA
Capacity: 1550mAh
60 ±5 s
<15 kg
<25 kg
>10 V/m
-10 °C...+50°C
-20 °C...+60 °C
<85 %rF, not con-
densing
IP41 / IK02
Publicité
