Locknetics MG600 Série Guide De L'utilisateur

Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

MG600/MG1200 Series
Electromagnetic Lock User's Guide
Description
The Electromagnetic Lock (Maglock) Series is a surface mounted magnetic lock assembly. It is a narrow profile model available in single
lock format with various sizes (force) designed for standard installation on most types of doors.
MG600 series
Specifications
DESCRIPTION
Holding Force
(lbs)
Lock
Input Voltage
(VDC)
Current Draw:
@ 12 VDC (amps)
@ 24 VDC (amps)
Relay Rating:
@ 120 VAC (amps)
@ 30 VDC (watts)
(resistive)
@ 60 VDC (amps)
Dimensions:
inches
(mm)
Weight:
Material:
Lock Housing
Armature / Strike Plate
Additional Features:
Precautions
● Shut off all power before attempting any wiring procedures.
● Maintain a clean & safe environment when working in public areas.
● Constantly be aware of pedestrian traffic around the door area.
● Always stop pedestrian traffic through the doorway when performing tests that may result in unexpected reactions by the door.
● Always check placement of all wiring before powering up to insure moving door parts will not catch any wires and cause
damage to equipment.
● Ensure compliance with all applicable safety standards and building codes upon completion of installation.
WARNING
Warnings indicate potentially hazardous
conditions, which if not avoided or corrected,
may cause death or serious injury.
MG1200
1200
Single
12 to 24
0.505
0.260
N/A
3W
N/A
10.54 x 2.87 x 1.59
9.84 x 1.86 x 1.02
(268 x 73 x 40.5)
(250 x 47.2 x 26)
lbs
10.5
(kg)
4.8
Aluminum
Zinc Plated Steel
Zinc Plated Steel
N/A
Cautions indicate potentially hazardous
conditions, which if not avoided or corrected,
may cause minor or moderate injury. Cautions
may also warn against unsafe practices.
MG600
MG1200DT
600
1200
Single
Single
12 to 24
12 to 24
0.505
0.505
0.260
0.260
N/A
N/A
3W
3W
N/A
N/A
10.54 x 2.87 x 1.59
(268 x 73 x 40.5)
10.0
10.5
4.5
4.8
Aluminum
Aluminum
Zinc Plated Steel
N/A
Door Status and Timer Door Status and Timer
CAUTION
CAUTION
MG1200 series
MG600DT
600
Single
12 to 24
0.505
0.260
N/A
3W
N/A
9.84 x 1.86 x 1.02
(250 x 47.2 x 26)
10.0
4.5
Aluminum
Zinc Plated Steel
NOTICE
Notices indicate a condition that may cause
equipment or property damage only.

Publicité

Table des Matières
loading

Sommaire des Matières pour Locknetics MG600 Série

  • Page 1 MG600/MG1200 Series Electromagnetic Lock User’s Guide Description The Electromagnetic Lock (Maglock) Series is a surface mounted magnetic lock assembly. It is a narrow profile model available in single lock format with various sizes (force) designed for standard installation on most types of doors. MG600 series MG1200 series Specifications...
  • Page 2: Installation Tips

    NOTICE 1. The product should only be powered by a UL listed power supply Regulated Power Limited power source. 2. Relay output is designated as Common. 3. Same Room Install – Resistive. 4. Installation Location: Indoor Dry. Installation & wiring in compliance with ANSI/NFPA70 requirements ...
  • Page 3 Installation - Electical Position the jumpers according to the input voltage, and then fi nish electrical connection to the door operator. When the maglock assembly and armature/strike plate are mated, the junction is Normally Open and the LED will turn to green. The remaining three terminals of the terminal block (COM/ NO/ NC) provide an auxiliary relay output which can be used as a door position switch.
  • Page 4 Installation - Mechanical Inspect the frame header to determine if an angle bracket or filler plate is required. Fold the enclosed mounting template on the dotted line and then mark and drill holes as indicated. Drill two 1/8” (3.1 mm) holes at the locations marked ‘B’.
  • Page 5: Spécifications

    Séries MG600/MG1200 Guide d’utilisation de la serrure électromagnétique Description La série de serrures électromagnétiques (serrures magnétiques) est un ensemble de serrures magnétiques posées en applique. Il s’agit d’un modèle au profil étroit disponible sous forme de serrure unique dans différentes tailles (forces) et conçu pour une installation standard sur la plupart des types de portes.
  • Page 6 AVIS 1. Le produit ne doit être alimenté que par une source d’alimentation limitée et régulée, homologuée UL. 2. La sortie de relais est désignée comme commune. 3. Installation dans une même pièce : résistive. 4. Emplacement d’installation : dans un local sec. Installation et câblage conformes aux exigences ANSI/NFPA70 ...
  • Page 7: Capteur De Porte

    Installation - Électrique Positionner les cavaliers en fonction de la tension d’entrée, puis terminer le branchement électrique au niveau du dispositif de fermeture de porte. Lorsque l’ensemble de serrure magnétique et le plateau d’armature/la gâche sont rassemblés, la jonction est normalement ouverte et la DEL devient verte. Les trois bornes restantes du bloc de jonction (COM/NO/NC) fournissent une sortie de relais auxiliaire pouvant servir de commutateur de position de porte.
  • Page 8: Montage

    Installation - Mécanique Inspecter le linteau du cadre pour déterminer si un support d’angle ou une fausse lame de charnière sont requis. Plier le gabarit de montage joint le long de la ligne pointillée, puis marquer et percer les trous comme indiqué. Percer deux trous de 3,1 mm (0,13 po) aux endroits marqués « B ». Pour les portes simples, placer le gabarit contre la porte et le linteau sur le côté...

Ce manuel est également adapté pour:

Mg1200 sérieMg600dtMg1200dt

Table des Matières