Table des Matières

Publicité

It is EXTREMELY IMPORTANT that you use DRY WOOD only in your wood stove. The wood should have dried for 9
to 15 months, such that the humidity content (in weight) is reduced below 20% of the weight of the log. It is very
important to keep in mind that even if the wood has been cut for one, two or even more years, it is not necessarily
dry, if it has been stored in poor conditions. Under extreme conditions it may rot instead of drying. This point
cannot be over stressed; the vast majority of the problems related to the operation of a wood stove is caused by
the fact that the wood used was too damp or had dried in poor conditions. These problems can be:
- ignition problems
- creosote build-up causing chimney fires
- low energy yield
- blackened windows
- incomplete log combustion
Smaller pieces of wood will dry faster. All logs exceeding 6" in diameter should be split. The wood should not
be stored directly on the ground. Air should circulate through the cord. A 24" to 48" air space should be left
between each row of logs, which should be placed in the sunniest location possible. The upper layer of wood
should be protected from the elements but not the sides.

OPERATIONAL TIPS

Operational Tips for Good, Efficient, and Clean Combustion
Get the appliance hot and establish a good coal bed before adjusting to a low burn rate (this may take
30 minutes or more depending on your wood)
Use smaller pieces of wood during start-up and a high burn rate to increase the stove temperature
Be considerate of the environment and only burn dry wood
Burn small, intense fires instead of large, slow burning fires when possible
Learn your appliance's operating characteristics to obtain optimum performance
Burning unseasoned wet wood only hurts your stoves efficiency and leads to accelerated creosote buildup in
your chimney
TESTING YOUR WOOD
When the stove is thoroughly warmed, place one piece of split wood (about five inches in diameter) parallel
to the door on the bed of red embers.
Keep the air control full open by pulling on it and close the door. If ignition of the piece is accomplished within
90 seconds from the time if was placed in the stove, your wood is correctly dried. If ignition takes longer, your
wood is damp.
If your wood hisses and water or vapor escapes at the ends of the piece, your wood is soaked or freshly cut.
Do not use this wood in your stove. Large amounts of creosote could be deposited in your chimney, creating
potential conditions for a chimney fire.
Never alter the damper slide or the adjustment range to increase firing for any reason. Doing so could result
TAMPER WARNINGS
This wood heater has a manufacturer-set minimum low burn rate that must not be altered. It is against federal
regulations to alter this setting or otherwise operate this wood heater in a manner inconsistent with operating
instructions in this manual.
THE FIRST FIRES
The fresh paint on your stove needs to be cured to preserve its quality. Once the fuel charge is properly
ignited, only burn small fires in your stove for the first four hours of operation. Never open the air control more
than necessary to achieve a medium burn rate.
Make sure that there's enough air circulation while curing the stove. The odors could be smelled during the 3
or 4 first fires. Never start your stove outside. You will not be able to see if you are over heating.
IGNITION
After making sure that the stove air intake controls are fully open (completely pull-out towards you), The top
down method of fire building is recommended for this appliance. After making sure that the stove air intake
controls are fully open (completely pull-out towards you), Place the largest pieces of wood on the bottom, laid
in parallel and close together. Smaller pieces are placed in a second layer, crossways to the first. A third layer
of still smaller pieces is laid crossways to the second, this time with some spaces between. Then a fourth layer of
loose, small kindling and twisted newspaper sheets tops off the pile.
CAUTION:
in heater damage and will void your warranty.
-14-

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

2000 ln2000 e

Table des Matières