Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
is 16 gauge has more capacity than 18 gauge. An undersized cord will cause a drop in line
voltage resulting in loss of power and overheating. When using more than one extension to
make up the total length, be sure each individual extension contains at least the minimum
wire size. The following table shows the correct size to use depending on cord length and
nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge
number, the heavier the cord.
CAUTION
: Blades coast after turn off. Serious personal injury may result.
WARNING
: AlWAyS wear proper personal hearing protection that conforms to ANSI
S12.6 (S3.19) during use. Under some conditions and duration of use, noise from this product
may contribute to hearing loss.
WARNING
: AlWAyS use proper eye protection. All users and bystanders must wear
proper eye protection that conforms to ANSI Z87.1.
WARNING
: AlWAyS USE SAfETy GlASSES. Everyday eyeglasses are NOT safety
glasses. Also use face or dust mask if cutting operation is dusty. ALWAYS wear certified safety
equipment:
• ANSI Z87.1 eye protection (CAN/CPA Z94.3),
• ANSI S12.6 (S3.19) hearing protection,
• NOSH/OSHA respiratory protection.
WARNING
: Some dust created by power sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known in the state of California to cause cancer, birth
defects or other reproductive harm. Some examples of these chemicals are:
• Lead from lead-based paints, crystalline silica from bricks and cement and other masonry
products, and arsenic and chromium from chemically-treated lumber (CCA).
Your risk from these exposures varies, depending on how often you do this type of work.
To reduce your exposure to these chemicals: work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that are specially designed to filter out
microscopic particles.
• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and
other construction activities. Wear protective clothing and wash exposed areas with
soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote
absorption of harmful chemicals.
WARNING
: Use of this tool can generate and/or disburse dust, which may cause serious
and permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory
protection appropriate for the dust exposure. Direct particles away from face and body. Always
operate tool in well-ventilated area and provide for proper dust removal. Use dust collection
system wherever possible.
SyMBOlS
The label on your tool may include the following symbols. The symbols and their definitions are as follows:
V .................. volts
Hz ................ hertz
min .............. minutes
or DC ... direct current
................ Class I Construction
(grounded)
................ Class II Construction
(double insulated)
............... Read instruction manual before use
................ Use proper eye protection
When using an extension cord, be sure to use
one heavy enough to carry the current your
product will draw. An undersized cord will
cause a drop in line voltage resulting in loss
of power and overheating. The following table
shows the correct size to use depending on
cord length and nameplate ampere rating. If in
doubt, use the next heavier gauge. The smaller
the gauge number, the heavier the cord.
A ...................amperes
W ..................watts
or AC .......alternating current
n o ..................no load speed
..................earthing terminal
.................safety alert symbol
.../min or rpm...revolutions or
reciprocation per minute
..................Use proper respiratory protection
..................Use proper hearing protection
Minimum Gauge for Cord Sets
Volts
120V
0-25
(0-7,6m) (7,6-15,2m) (15,2-30,4m) (30,4-45,7m)
240V
0-50
(0-15,2m) (15,2-30,4m) (30,4-60,9m) (60,9-91,4m)
Ampere Rating
More Not more
Than Than
0 -
6
18
6 -
10
18
10 -
12
16
12 -
16
14
4
Total length of Cord in feet
26-50
51-100
101-150
51-100
101-200
201-300
American Wire Gauge
16
16
16
14
16
14
12
Not Recommended
14
12
12
Publicité
Table des Matières
