Eurotops B/6601 Mode D'emploi page 6

B/6601
Warning: Please read this instruction manual carefully before using the instrument
and keep it for future use.
Compatible with the following models:
- S 6601
IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY
The battery is not fully charged when you first receive it. First read the safety instructions
below the follow charging notes and procedures.
READ ALL INSTRUCTIONS CAREFULLY AND KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.
The battery needs to be charged before first use and whenever it fails to produce sufficient
power on jobs that were easily done before.
The battery may become warm while charging; this is normal and does not indicate a
problem.
NOTE: After several charge and discharge cycles, the battery will attain full capacity.
1. Do not incinerate the battery even if it is severely damaged or is completely worn out.
The battery can explode in a fire.
2. A small leakage of liquid from the battery cells may occur under extreme usage or
temperature conditions. This does not indicate a failure. However, if the outer seal is
broken and this leakage gets on your skin:
a. Wash quickly with soap and water.
b. Neutralize with a mild acid such as lemon juice or vinegar.
c. If battery liquid gets in your eyes, flush them with clean water for a minimum of
minutes and seek immediate medical attention.(medical notes: the liquid is 25-35%
solution of potassium hydroxide.)
3. Do not connect the positive pole and the negative pole of the battery with any metal
objects. Battery could be short circuited causing damage to the battery and possibly
causing severe burns or fire.
4. Charge the battery only in the chargers supplied with the product.
5. NOTE: the battery in your tool is the lithium-ion type, with no self-discharge or
memory effect.
6. Never attempt to open or modify battery for any reason. Released electrolyte is corrosive
and may cause damage to eyes and skin. It may be toxic if swallowed.
7. Under extreme conditions, battery leakage may occur. When you notice liquid on the
battery, proceed as follows:
• Carefully wipe the liquid off using a cloth. Avoid skin contact.
LITHIUM 10.8V
• The battery fluid, a 25-30% solution of potassium hydroxide, can be harmful. In case of
EN
skin contact, immediately rinse with water. Neutralize with a mild acid such as lemon
juice or vinegar. In case of eye contact, rinse abundantly with clean water for at least 10
minutes.
8. Do not expose to water.
9. Do not store in locations where the temperature may exceed 104°F (40°C).
10. Charge at room temperature: 64°F-75°F (18°C-24°C), never at ambient temperatures
below 40°F (4°C) and above 104°F (40°C).
11. Charge only using the charger provided with the tool.
12. Before charging, make sure that the battery is dry and clean.
13. Use only the correct type of battery for the tool.
14. Exercise care in handling and storing batteries in order not to short them with conductive
materials such as rings, keys, coins. There is a real risk of the battery or the conductor
overheating, causing fire or burns.
A. Insert / remove the battery
 Always release the On/Off switch before insertion or removal of the battery pack.
 To remove the battery pack, withdraw it from the tool while pressing the spring
button at the bottom of the cartridge.
 To insert the battery pack, align the tongue on the battery cartridge with the groove
in the housing and slip it into place. Always insert it all the way until it locks in place
with a little click. If not, it may accidentally fall out of the tool, causing injury to you
or someone around you.
 Do not use force when inserting the battery pack. If the cartridge does not slide in
easily, it is not being inserted correctly.
B. Battery charging
Do not use other battery chargers than the one supplied with S 6601 devices.
Observe correct mains voltage: The voltage of the power source must agree with the voltage
specified on the nameplate of the unit. Equipment marked with 230 V can also be connected
to 220 V or 240 V.
The Li-ion battery is protected against deep discharging by the "Electronic Cell Protection".
When the battery is empty, the machine is switched off by means of a protective circuit: The
inserted tool no longer rotates.
WARNING: Do not continue to press the On/Off switch after the machine has been
automatically switched off. The battery can be damage.
The battery is supplied partially charged. To ensure full capacity of the battery, completely
charge the battery in the battery charger before using your power tool for the first time.
A battery that is new or has not been used for a longer period does not develop its full
capacity until after approx. 5 charging/discharging cycles.
When the machine can not rotate while the On/Off switch is pressed, then the battery has
no enough capacity and should be charged.
1. After normal usage, your battery pack should be fully charged in about 1 hours.
Allow the battery to cool down before charging after using the saw. (NOTE: A hot
6