Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
could give the operator an electric shock.
• Keep hands away from the sawing range. Do
not reach under the workpiece. Contact with
the saw blade can lead to injuries.
• Apply the machine to the workpiece only when
switched on. Otherwise there is danger of kick-
back when the cutting tool jams in the workpiece.
• When sawing, the base plate must always faces
against the workpiece. The saw blade can
become wedged and lead to loss of control over
the machine.
• When the cut is completed, switch off the
machine and then pull the saw blade out of the
cut only after it has come to a standstill. In this
manner you can avoid kickback and can place
down the machine securely.
• Use only undamaged saw blades that are in per-
fect condition. Bent or dull saw blades can break,
negatively influence the cut, or lead to kickback.
• Do not brake the saw blade to a stop by applying
side pressure after switching off. The saw blade
can be damaged, break or cause kickback.
• Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the workpiece by hand or against your
body leaves it unstable and may lead to loss of
control.
• Use appropriate detectors to determine if utility
lines are hidden in the work area or call the lo-
cal utility company for assistance. Contact with
electric lines can lead to fire and electric shock.
Damaging a gas line can lead to explosion. Pe-
netrating a water line causes property damage.
• When working with the machine, always hold it
firmly with both hands and provide for a secure
stance. The power tool is guided more secure
with both hands.
• Secure the workpiece. A workpiece clamped
with clamping devices or in a vice is held more
secure than by hand.
• Always wait until the machine has come to a
complete stop before placing it down. The tool
insert can jam and lead to loss of control over
the power tool.
SAFETY WARNINGS FOR BATTERY
a) Do not open the battery. Danger of short-
circuiting.
b) Protect the battery against heat, e. g., against
continuous intense sunlight, fire, water, and
moisture. Danger of explosion.
WWW.VONROC.COM
c) In case of damage and improper use of the bat-
tery, vapours may be emitted. Ventilate the area
and seek medical help in case of complaints.
The vapours can irritate the respiratory system.
d) Use the battery only in conjunction with your
Vonroc product. This measure alone protects
the battery against dangerous overload.
e) The battery can be damaged by pointed objects
such as nails or screwdrivers or by force
applied externally. An internal short circuit can
occur and the battery can burn, smoke, explode
or overheat.
SAFETY WARNINGS FOR CHARGER
Intended use
Charge only CD801AA and CD803AA type rechargea-
ble Battery packs with the charger. Other types of bat-
teries may burst causing personal injury and damage.
a) The appliance is not to be used by persons
(including children) with reduced physical, sen-
sory or mental capabilities, or lack of experien-
ce and knowledge, unless they have been given
supervision or instruction.
b) Children being supervised not to play with the
appliance.
c) Do not recharging non-rechargeable batteries!
d) During charging, batteries must be placed in
the well ventilated area!
Electrical safety
Always check that the voltage of the power
supply corresponds to the voltage on the
rating plate.
• Do not use the machine if the mains cable or
the mains plug is damaged.
• Only use extension cables that are suitable
for the power rating of the machine with a
minimum thickness of 1.5 mm
tension cable reel, always fully unroll the cable.
2. MACHINE INFORMATION
Intended use
The machine is intended for sawing wood, plastic and
metal while keeping the baseplate resting firmly on
the workpiece. It is suitable for straight and curved
cuts. It is also possible to cut flush to the workpiece
surface. A suitable saw blade must always be used.
EN
. If you use a ex-
2
7
Publicité
Table des Matières
