JVC KD-R484 Mode D'emploi page 14

AUDIO SETTINGS
LEVEL 01/LEVEL 02: Boosts low or high frequencies to produce a well-
LOUDNESS
balanced sound at low volume. ; OFF: Cancels.
SPK-OUT * 5
SUB.W LEVEL * 4
PRE-OUT * 6
SUBWOOFER SET * 6 ON: Turns on the subwoofer output. ; OFF: Cancels.
SUBWOOFER LPF *
4 FRQ THROUGH: All signals are sent to the subwoofer ;
FRQ 55HZ/FRQ 85HZ/FRQ 120HZ: Audio signals with frequencies lower
than 55 Hz/85 Hz/120 Hz are sent to the subwoofer.
SUB.W PHASE * 4 REVERSE (180°)/NORMAL (0°): Selects the phase of the subwoofer
output to be in line with the speaker output for optimum performance.
(Selectable only if a setting other than [FRQ THROUGH] is selected for
[SUBWOOFER LPF].)
POSITION R06 to POSITION F06 (POSITION 00): Adjusts the front and
FADER
rear speaker output balance.
BALANCE * 7 POSITION L06 to POSITION R06 (POSITION 00): Adjusts the left and
right speaker output balance.
LEVEL –15 to LEVEL +06 (LEVEL 00): Preset the initial volume level of
VOLUME ADJUST
each source (compared to the FM volume level). Before adjustment, select
the source you want to adjust. ("VOL ADJ FIX" appears if FM is selected.)
LOW POWER: Limits the maximum volume level to 25. (Select if the
AMP GAIN
maximum power of each speaker is less than 50 W to prevent damaging
the speakers.) ; HIGH POWER: The maximum volume level is 35.
* 4
Displayed only when [SUBWOOFER SET] is set to [ON].
* 5
Displayed only when [SPK/PRE OUT] is set to [SUB.W/SUB.W].
* 6
Displayed only when [SPK/PRE OUT] is set to [REAR/SUB.W] or [SUB.W/SUB.W].
* 7
This adjustment will not affect the subwoofer output.
10
ENGLISH
SUB.W 00 to SUB.W +06 (SUB.W +03): Adjusts the
output level of the subwoofer connected via speaker lead.
( 16)
SUB.W –08 to SUB.W +08 (SUB.W 00): Adjusts the
output level of the subwoofer connected to the lineout
terminals (REAR/SW) through an external amplifier.
( 16)
ON: Creates realistic sound by compensating the high-frequency
D.T.EXPANDER
components and restoring the rise-time of the waveform that are lost in
(Digital Track
audio data compression. ; OFF: Cancels.
Expander)
Depending on the speaker connection method, select the appropriate
SPK/PRE OUT
setting to get the desired output. ( Speaker output settings)
Speaker output settings
Select the output setting for the speakers [SPK/PRE OUT], base on the
speaker connection method.
Connection via lineout terminals
For connections through an external amplifier. ( 16)
Setting on
[SPK/PRE OUT]
REAR/REAR Rear speakers output
REAR/SUB.W (default) Subwoofer output
SUB.W/SUB.W Subwoofer output
Connection via speaker leads
For connections without using an external amplifier. However, with
this settings you can also enjoy the subwoofer output. ( 16)
Setting on
[SPK/PRE OUT]
REAR/REAR Rear speakers output
REAR/SUB.W (default) Rear speakers output
SUB.W/SUB.W Subwoofer output
If [SUB.W/SUB.W] is selected:
– [FRQ 120HZ] is selected in [SUBWOOFER LPF] and [FRQ THROUGH] is not
available.
– [POSITION R01] is selected in [FADER] and selectable range is
[POSITION R06] to [POSITION 00].
Audio signal through lineout terminal
REAR/SW
Audio signal through rear speaker lead
L (left) R (right)
Rear speakers output
Rear speakers output
(Mute)