ADEO SCREEN ALUMID Manuel D'installation Et D'utilisation page 11

Masquer les pouces Voir aussi pour ALUMID:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 14
ENGLISH – Rolling screen installation and operation manual
The type of motor installed on the product is identified by a label applied on each product showing the CE logo. When unwrapping the product please check the model type indicated on the label in order to
perform the installation and cable connections correctly. Should the power of the motor be different from that of the supply network of the installation place, please contact an electrician to have a current and
Hz transformer installed.
ELECTRICAL CONNECTION:
electric cabling must be conformant with applicable IEC standards. IEC norm EN 60335-1 requires
that supply network be fitted with an omnipolar selector switch with contact opening distance of at
least 3 mm. For the screen's control use only the selector switch provided by manufacturer, or
equivalent model, and follow the instructions of the connection diagram shown on left (if the motor is
mounted on the left, the colours of the wires must be inverted, i.e. descending = brown, ascending =
black). The selector switch must be mounted within sight distance of the product, at a 1.5 - 1.8 m
height from the floor. To connect the wires to the supplied switch, remove the plastic front plates to
access the lock/unlock buttons
Correctly performed, state-of-the-art, norm-compliant electrical connections are important to prevent accidents and to ensure the screen's
optimal and unaltered performance over time. Prior to carrying out any operation on electrical parts ensure that power supply is disconnected. In
screens fitted with cases the motor is positioned on the right-hand side of the screen as seen from the front (upon request it can be located on
the left). Never connect two or more motors to the same selector switch without a control unit or two switches to the same motor..
electric cabling must be conformant with applicable IEC standards. IEC norm EN 60335-1 requires that supply network be fitted with an
omnipolar selector switch with contact opening distance of at least 3 mm. For each motor (e.g. plug switch etc.). In case of need, this device
ensures that the power supply is safely and quickly cut off. Use the wires as described in the figure.
Correctly performed, state-of-the-art, norm-compliant electrical connections are important to prevent accidents and to ensure the screen's
optimal and unaltered performance over time. Prior to carrying out any operation on electrical parts ensure that power supply is disconnected.
Bus cables (black white orange) must be insulated if not used for the push-button command.
In screens fitted with cases the motor is positioned on the right-hand side of the screen as seen from the front (upon request it can be located on
electric cabling must be conformant with applicable IEC standards. IEC norm EN 60335-1 requires that supply network be fitted with an
omnipolar selector switch with contact opening distance of at least 3 mm. For each motor (e.g. plug switch etc.). In case of need, this device
ensures that the power supply is safely and quickly cut off. Use the wires as described in the figure.
Correctly performed, state-of-the-art, norm-compliant electrical connections are important to prevent accidents and to ensure the screen's
optimal and unaltered performance over time. Prior to carrying out any operation on electrical parts ensure that power supply is disconnected.
In screens fitted with cases the motor is positioned on the right-hand side of the screen as seen from the front (upon request it can be located on
Made by Adeo Screen Sp. Z o.o. (Poland) Specifications are subject to change without notice. E&OE
Doc: ALUMID Installation Manual rev3 | 29.12.2020
Please verify that you are working with the latest revision of this document before specifying your screen.
09 MOTOR TYPE IDENTIFICATION –CHARACTERISTICS – ELECTRICAL CONNECTION
WARNING:
ELECTRICAL CONNECTION:
WARNING:
the left).
Operates with standard radio control (supplied).
ELECTRICAL CONNECTION:
WARNING:
the left).
Operates with standard radio control (supplied).
230V 50Hz
Motor characteristics:
Frequency: ~Hz50
Power: 120W
Torque: 15Nm
Speed: 12Rpm
Duty cycle: S2 4min
Cable length: 2.5m
Mechanical strength: EN14202 conformant
Operating T°: from –20 to +55 °C
Weighted sound pressure level:
LpA ≤ 70 dB(A)
Motor protection class: IP44
Connection for each motor:
Brown (Up)
Black (Down)
Blue (Common)
Yellow Green (Ground 230V)
Somfy RTS 230V 50Hz
Technical characteristics:
Frequency: ~Hz50
Power: 140W
Torque: 15Nm
Speed: 17Rpm
Duty cycle: S2 4min
Cable length: 3m
Operating T°: from –20 to +55 °C
Frequency: 433.92 MHz
Trans. range: 150m
Weighted sound pressure level: LpA ≤ 70 dB(A)
Motor protection class: IP44
Connection for each motor:
Brown (Phase 230V)
Blue (Neutral 230V)
Yellow Green (Ground 230V)
Somfy IO 230V 50Hz
Technical characteristics:
Frequency: ~Hz50
Power: 80W
Torque: 15Nm
Speed: 17Rpm
Duty cycle: S2 4min
Cable length: 2.5m
Mechanical strength: EN14202 conformant
Operating T°: from –20 to +55 °C
Frequency: 868-870 MHz
Weighted sound pressure level: LpA ≤ 70 dB(A)
Motor protection class: IP44
Connection for each motor:
Brown (Up)
Black (Down)
Blue (Neutro 230V)
Grey (Phase 230V)
Page 11

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Pronalumid sériePronalumid-xxxxx

Table des Matières