Dust/Chip Extraction; Operating Modes; Starting Operation - Bosch GKT 55 GCE Professional Notice Originale

OBJ_BUCH-1471-003.book Page 17 Friday, November 27, 2015 8:58 AM
Mounting the Saw Blade (see figure A)
Adjust the maximal cutting depth, see section "Adjusting the
Cutting Depth".
For changing the cutting tool, it is best to place the machine
on the face side of the motor housing.
– Pivot lever 3 toward the front.
– Push lock-off button 2 toward the front and press the saw
toward base plate 7 until it engages in the position for
changing the saw blade.
– Clean the saw blade 22 and all clamping parts to be assem-
bled.
– Place the saw blade 22 on to the mounting flange 23. The
cutting direction of the teeth (direction or arrow on saw
blade) and the direction-of-rotation arrow on the blade
guard 15 must correspond.
– Mount the clamping flange 21 and screw in the clamping
bolt 20 turning in rotation direction . Observe correct
mounting position of mounting flange 23 and clamping
flange 21.
– Press the spindle lock button 25 and keep it pressed.
– With the hex key 5, tighten the clamping bolt 20 turning in
rotation direction . The tightening torque is between
6–9 Nm, which corresponds to hand tight plus ¼ turn.
– Pivot lever 3 back. When doing this, the saw retracts back
to the starting position.

Dust/Chip Extraction

 Before any work on the machine itself, pull the mains
plug.
 Dust from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one's health. Touching or breathing-in the dust can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
Certain dust, such as oak or beech dust, is considered car-
cinogenic, especially in connection with wood-treatment
additives (chromate, wood preservative). Materials con-
taining asbestos may only be worked by specialists.
– As far as possible, use a dust extraction system suitable
for the material.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
 Prevent dust accumulation at the workplace. Dust can
easily ignite.
External Dust Extraction
Mount the vacuum hose 31 (accessory) on to the chip ejector
18. Connect the vacuum hose 31 to a vacuum cleaner (acces-
sory). An overview for connecting to various vacuum cleaners
can be found at the end of this manual.
The machine can be plugged directly into the receptacle of a
Bosch all-purpose vacuum cleaner with remote starting con-
trol. The vacuum cleaner starts automatically when the ma-
chine is switched on.
Bosch Power Tools
The vacuum cleaner must be suitable for the material being
worked.
When vacuuming dry dust that is especially detrimental to
health or carcinogenic, use a special vacuum cleaner.
Operation

Operating Modes

 Before any work on the machine itself, pull the mains
plug.
Adjusting the Cutting Depth (see figure B–C)
 Adjust the cutting depth to the thickness of the work-
piece. Less than a full tooth of the blade teeth should be
visible below the workpiece.
Turn cutting-depth indicator 8 to the bottom position  for
sawing without guide rail, or to the upper position  for saw-
ing with guide rail.
Press slider 27 and adjust the desired cutting depth (material
thickness + tooth height of the saw blade) on cutting-depth
scale 6.
Adjusting the Cutting Angle
Loosen the wing bolts 11 and 17. Tilt the saw sidewards.
Adjust the desired measure on the scale 9. Tighten the wing
bolts 11 and 17 again.
The mitre angle of the saw can be adjusted to – 1 ° or +47 °.
For the – 1 ° mitre angle, additionally push button 16 while
tilting, or for the +47 ° mitre angle, push button 12 while tilt-
ing.
Note: For bevel cuts, the cutting depth is smaller than the set-
ting indicated on the cutting-depth scale 6.
Cutting Marks (see figure D)
The 0° cutting mark (32) indicates the position of the saw
blade for straight cuts. The 45° cutting mark (33) indicates
the position of the saw blade for 45° cuts without using the
guide rail.

Starting Operation

 Observe correct mains voltage! The voltage of the
power source must agree with the voltage specified on
the nameplate of the machine. Power tools marked
with 230 V can also be operated with 220 V.
Switching On and Off
To start the machine, first push the lock-off button for the
On/Off switch 2 and then press the On/Off switch 1 and keep
it pressed.
Actuating lock-off button 2 releases the plunging device at the
same time, and allows for the saw to be pushed down. This
makes the saw blade plunge into the workpiece. When pulling
up, the saw retracts to the starting position and the plunging
device is locked again.
To switch off the machine, release the On/Off switch 1.
Note: For safety reasons, the On/Off switch 1 cannot be
locked; it must remain pressed during the entire operation.
To save energy, only switch the power tool on when using it.
English | 17
1 609 92A 1SZ | (27.11.15)