Scope Of Use; General Safety Instructions - EINHELL PROFI SILVER LINE PS-WS 2300-230 Mode D'emploi

Anleitung PS-WS 2300-230_SPK1
GB
Thank you for buying this angle grinder.
Your new angle grinder is easy to use and highly ver-
satile – an indispensable tool for all DIY enthusiasts.
This tool complies with the requirements of the
Equipment Safety Law and the relevant standards.
When using electrical equipment, a few safety pre-
cautions must be observed to avoid injuries and dam-
age. Please read the complete operating manual with
due care. Retain this manual in a safe place, so that
the information is available at all times. If you give the
equipment to any other person, hand over this oper-
ating manual as well.
We accept no liability for damage or accidents which
arise due to non-observance of these instructions.
We hope that you enjoy using your angle grinder.

1. SCOPE OF USE

This angle grinder is designed to cut, rough, brush,
grind and polish metal and masonry using the appro-
priate accessories. It is also designed for cutting the
heads off screws and for cleaning and smoothing
surfaces before and after welding work.

2. GENERAL SAFETY INSTRUCTIONS

The following basic safety action measures
should be taken when using electric tools to
protect the user from electric shocks and
the risk of injury and fire. Read and follow these
instructions before using this electric tool. Do not lose
these safety regulations.
For safe working:
Keep your work area tidy
- An untidy work area invites accidents.
Make allowance for ambient conditions
- Do not expose electric tools to rain. Never use
electric tools in damp or wet locations. Provide
good lighting. Never use electric tools anywhere
where there is a risk of fire or explosion.
Guard against electric shock
- Avoid bodily contact with earthed parts (e.g.
pipes, radiators, cookers and refrigerators).
Keep children away
- Do not allow other persons to touch the electric
tool or cable. Keep other persons away from your
work area.
Keep your electric tools in a safe place
- When not in use, electric tools should be kept in
a dry place out of reach of children at a good
height or under lock and key.
Do not overload your electric tools
- Tools work better and safer when used within
10
18.08.2005 15:29 Uhr Seite 10
their quoted capacity range. Never overload the
tool unnecessarily as this could pose a risk to the
operator or impair the proper functioning of the
tool.
Use the right electric tool
- Never use tools or attachments with insufficient
power for the job in hand. Never use the electric
tool for purposes other than that for which it is
designed.
Wear suitable work clothes
- Do not wear loose clothing or jewelry as they
may get caught in moving parts. Rubber gloves
and non-slip shoes are recommended when wor-
king outdoors. Wear a hair net if you have long
hair.
Wear eye protection and ear plugs at all times.
Wear ear plugs
The impact of noise can cause damage to
hearing.
Wear safety goggles.
Sparks generated during working or
splinters, chips and dust emitted by the tool
can cause loss of sight.
Personal safety equipment such as a breathing
mask (especially for work which generates dust),
gloves, apron and a helmet should also be worn.
Wear a breathing mask.
Harmful dust can be generated when
working on metals and other materials.
Never use the tool to work on any
materials containing asbestos!
Do not use the cable for purposes for which
is not designed
- Never carry your electric tool by its cable. Do
not use the cable to pull the plug out of the
socket. Protect the cable from heat, oil and sharp
edges.
Secure your workpiece
- Use clamps or a vise to hold the workpiece
securely. This is far safer than holding it in your
hand and also means that you have both hands
free to operate the electric tool.
Avoid abnormal working postures.
- Make sure you stand squarely and keep your
balance at all times.
Take care of your electric tools
- Keep the tool clean at all times so that you can
use it more easily and in safety. Check the elec-