Publicité
Les langues disponibles
Les langues disponibles
operations different from those intended could result
in a hazardous situation.
h ) Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations.
5) Battery Tool Use and Care
a ) Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used
with another battery pack.
b ) Use power tools only with specifically designated
battery packs. Use of any other battery packs may
create a risk of injury and fire.
c ) When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins,
keys, nails, screws, or other small metal objects,
that can make a connection from one terminal to
another. Shorting the battery terminals together may
cause burns or a fire.
d ) Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help. Liquid
ejected from the battery may cause irritation or burns.
e ) Do not use a battery pack or tool that is
damaged or modified. Damaged or modified
batteries may exhibit unpredictable behaviour
resulting in fire, explosion or risk of injury.
f ) Do not expose a battery pack or tool to fire
or excessive temperature. Exposure to fire or
temperature above 265 °F (130 °C) may cause
explosion.
g ) Follow all charging instructions and do not
charge the battery pack or tool outside the
temperature range specified in the instructions.
Charging improperly or at temperatures outside the
specified range may damage the battery and increase
the risk of fire.
6) Service
a ) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
b ) Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorized service providers.
Additional Safety Rules for Crimping Tool
DANGER: Use only approved connectors,
dies and cables in manufacturer-approved
combinations for successful installation.
Combining materials not approved by
manufacturers can result in faulty installations.
Faulty installations can result in catastrophic
failures, injury to installers and damage to
property.
DANGER: To reduce the risk of serious injury,
turn off power to the electrical lines before
making a crimp. Failure to shut off power prior
to work could result in severe injury or death and
property damage.
WARNING: Use the crimping tool only with
D
WALT-approved dies. Other uses or modifying
e
the crimping tool for other applications may
damage the crimping tool, damage the dies
and/or cause personal injury or create defective
connections.
WARNING: Though this D
will reach the proper pressure to complete a
crimp successfully, connections can only be
effective when the connection is free from
defects and when the crimp is properly prepared
according to the connector manufacturer's
installation procedures. Proper preparation and
installation is the responsibility of the installing
contractor.
•
Keep all body parts away from the hydraulic ram
and dies during operation and any time the power is
ON. A moment of inattention while operating power
tools, may result in serious personal injury. Fingers
or hands can be crushed, fractured or amputated if they
become caught in the dies or moving parts.
•
Inspect tool and dies before use. Never attempt
to repair a damaged crimping tool head or dies. A
die that has been modified in any way can crack during
crimping resulting in serious injury. Discard the entire
damaged die. Replacement or repair of tool head may be
required.
•
This tool produces large forces that can break dies
or parts and cause injury. Always be attentive and
take proper safety precautions, including wearing eye
protection.
Crush hazard. Never run the tool without
•
appropriate dies installed.
•
Only trained personnel should operate this tool.
•
Before operating, inspect the tool and LEDs on the
diagnostics panel. Correct any problems before using
the tool. Reference the Troubleshooting section for a list
of possible problems and solutions.
Before operating the D
•
e
tool, read and understand all safety and operating
instructions including the connector manufacturer's
installation instructions and the instructions for
any other equipment used with this tool. Failure to
follow all instructions and warnings may result in
property damage and/or serious personal injury.
•
Keep the crimping area of the tool free from hands
and other objects while tool is in use. Fingers could
be crushed.
•
Secure and support the material prior to making the
crimp to prevent movement during crimping.
Follow connector manufacturer's installation
•
instructions. Other uses may cause damage to the tool,
accessories, and workpiece.
•
Keep a firm grip on the tool at all times. Forces on the
tool may change during and after the crimp.
English
WALT crimping tool
e
WALT DCE300 crimping
3
Publicité
