Troubleshooting, What To Do - Brandt VI 320 Guide D'utilisation

Présentation de votre lave-vaisselle

Troubleshooting, what to do?

If you are in any doubt about the operation of your machine, before calling a qual-
ified engineer, check the following points (depending on the symptoms noticed).
When first using the machine Possible causes
- The machine is wobbly,
Small door leak
not level
- The door is not correct-
ly centred on the tub
- The seal's lip has been
flattened during storage
- Leak at the tap
Small leak around or
under the machine (move
- Leak in the machine
the machine to locate the
leak better)
The door "catches" when - The machine or the
door is not correctly
you close it
centred on the tub
- The door springs are
The door falls down
not tensioned enough
heavily when you open it
to compensate for the
(integratable models)
weight of the basket.
The door is not level - The door springs are
over-tensioned.
when open or goes back
up too quickly (integrat-
- No wooden panel
able machine)
- Poor handling (the bas-
The upper basket will not
ket has been pulled
stay in the high position
upwards too quickly).
Programming, display anomalies Possible causes
- The energy-saving pro-
The cycle takes too long.
grammes take longer
because they compensate
for the lower washing and
drying temperatures by
longer agitation and drying.
48
What to do
- Adjust the adjustable
feet
- Adjust the rear feet
- Take off the door seal
.
all around the door.
- Check that the seal is pre-
sent and re-tighten the nut
- Close the water tap and
call an engineer.
- Recentre the door by
adjusting the rear feet.
- Contact the installer.
- Tighten the two tensioning
screws accessible through
the holes in the two side
panels.
- Contact the installer.
- Loosen the two tensioning
screws accessible through
the holes in the two side
panels.
- Fit a wooden panel to the
door (a chipboard panel OK
if on a temporary basis)
and adjust the springs.
- Contact the installer.
- Move the basket gradu-
ally on one side and
then the other (until
you hear a "Click") = ->
see the Operating Instructions.
What to do
- Use these programmes
preferably at night
when the length and
the finishing time are
not important.
GB
Présentation de votre lave-vaisselle Troubleshooting, what to do?
Programming, display anomalies Possible causes
The lights light up one - Wrongly programmed.
after another
The Salt light does not go - No salt or too little salt
out in the reservoir to trig-
ger the float.
Poor operation Possible causes
The machine cuts off - Insufficient amperage to
supply all the equip-
ment being used at the
same time.
- Internal fault in the
machine
The machine will not - No power supply to the
start socket
- The tap is closed
- The water supply hose
is kinked
- Programme selection
error and programme
blocked
- "Start" button held down
too long (> 2 seconds)
- Safety system (anti-leak)
The machine does not - Protective cover on the
drain. sink's U bend not removed
- Drainage hose kinked
- Drain filter totally
blocked
- Pump blocked.
GB
What to do
- Cancel the current pro-
gramme by holding
down the "Start" button
for 3 seconds and then
reprogramme.
- Fill the reservoir and
wait until the cycle
ends. If the water is
soft enough not to
require salt, the Salt
light is permanently lit.
What to do
- Check the plug's ampe-
rage (10A minimum)
and the meter's capacity
- Call an engineer.
- Check the socket and
the fuse
- Check that the tap is
open
- Check that hose run
- Cancel by pressing
"Start" for 3 seconds
and reprogramme
- Press "Start" only briefly
to start the programme
- Call an engineer.
- Remove the protective
cover
- Check the hose runs cor-
rectly behind the machine
- Remove the filters and
clean them and the
drain hole
- Start a soak programme.
If the fault persists, call
an engineer.
49