Bosch PMF 250 CES Notice Originale page 17

OBJ_BUCH-1645-005.book Page 17 Wednesday, November 11, 2015 12:42 PM
Accessory
Scraper, rigid
BIM serrated seg-
ment saw blade
Mounting/Replacing the Application Tool/Accessory
(see figures A – C)
 If required, remove an already mounted application
tool/accessory. For this, push SDS lever 1 out of the lock-
ing position and sidewards.
To release the tool retainer 14, turn the SDS
lever approx. 3 turns in anticlockwise direc-
tion.
Note: Do not turn the SDS lever 1 further than necessary,
otherwise the tool retainer 14 can fall out of the gear head
(see "Inserting the Tool Retainer", page 17).
 Remove the application tool/accessory.
 Position the new application tool/accessory (e.g. plunge
cut saw blade 9) with its opening above the tool retainer
14. Move it on the tool holder 8 so that the recesses of the
application tool/accessory engage in the cams of the tool
holder.
To achieve a safe and low-fatigue working stance, the ap-
plication tools/accessories can be mounted on the tool
holder in any locking position. Mount the application
tool/accessory with the off-set facing downward (as
shown in the figure).

Turn the SDS lever 1 clockwise to lock the tool
retainer 14 and clamp the application tool/
accessory. Hand-tighten the SDS lever.
 When the SDS lever is not positioned directly above the
locking position, turn it back in anticlockwise direction
until it is located above the locking position. In no-load,
the SDS lever can be turned back by one turn (max.).
Turn the SDS lever until it is located directly above the
locking position.
 Press SDS lever 1 down so that it can be heard to engage
in the locking position.
 Check the tight seating of the application tool/accessory.
Incorrect or not securely fastened application tools/accesso-
ries can come loose during operation and pose a hazard.
Inserting the Tool Retainer (see figure D)
When the SDS lever 1 was opened too far, the tool retainer 14
can fall out of the gear head.
Insert the tool retainer 14 into the gear head in such a manner
that its flat side fits into the opening. Turn the SDS lever 1
clockwise.
Mounting and Adjusting the Depth Stop
The depth stop 12 can be used when working with segment
saw blades, Riff-segment saw blades and segment blades.
Bosch Power Tools
Material Application
Carpets, coverings Scraping on hard surfaces;
example: removing carpet and tile adhesive
Insulation material, insula- Cutting soft materials
tion panels, floor panels,
sound insulation panels,
cardboard, carpet, rub-
ber, leather
If required, remove an already mounted application tool/ac-
cessory.
Slide the depth stop 12 over and beyond the tool holder 8 to
the stop onto the gear head of the power tool with the labelled
side facing upward.
The depth stop is intended for the following cutting depths:
– With segment saw blades ACZ 85 .. with a diameter of
85 mm: 8 mm, 10 mm, 12 mm and 14 mm cutting depths
(see indication on the depth stop in large font and not in
brackets).
– With segment saw blades ACZ 100 .. with a diameter of
100 mm: 14 mm, 16 mm, 18 mm and 20 mm cutting
depths (see indication on the depth stop in smaller font
and brackets).
Insert the appropriate segment saw blade for the desired cut-
ting depth. Slide the depth stop 12 from the tool holder 8 in
the direction of the application tool until you can rotate it free-
ly. Rotate the depth stop 12 so that the desired cutting depth
is above the section of the saw blade, which will be used to
saw. Slide the depth stop 12 once again to the stop onto the
gear head of the application tool.
For all other cutting depths and when working with other ap-
plication tools, remove the depth stop 12. For this, remove
the application tool and pull the depth stop from the gear
head.
Mounting/Replacing a Sanding Sheet on the Sanding
Plate
The sanding plate 10 is fitted with Velcro backing for quick
and easy fastening of sanding sheets with Velcro adhesion.
Before attaching the sanding sheet 11, free the Velcro back-
ing of the sanding plate 10 from any debris by tapping against
it in order to enable optimum adhesion.
Position the sanding sheet 11 flush alongside one edge of the
sanding plate 10, then lay the sanding sheet onto the sanding
plate and press firmly.
To ensure optimum dust extraction, pay attention that the
punched holes in the sanding sheet match with the holes in
the sanding plate.
To remove the sanding sheet 11, grasp it at one of the tips and
pull it off from the sanding plate 10.
You can use all sanding sheets, fleece pads/polishing cloth
pads of the Delta 93 mm series of Bosch accessory program.
Sanding accessories, such as fleece pads/polishing cloth
pads, are attached to the sanding plate in the same manner.
English | 17
1 609 92A 1R3 | (11.11.15)