HOESCH ADANA-L-90 Instructions De Montage page 4

01 General information
Hoesch products set the benchmark for quality, comfort
and design. To assure optimal function and a long life
cycle of your product please comply with the following
instructions. Each delivery is strictly controlled before
leaving the factory. Check the completeness of the
delivery before starting installation. Products represented
here are subject to technical and visual modifi cations!
All dimensions data is in mm. All connection measures
are internal measurements! We are not liable for defects
resulting from non-conventional usage, improper transport
or faulty intermediate storage. Our respectively valid
warranty conditions are in force.
During mounting protect the surface of shower tray with
cover!
Do not put glass panes on rims or corners!
Caution! Check the delivery for transport
⚠
damage! Later claims will not be accepted!
The choice of raw plug and screws depends
upon the wall's material!
■ Water connections
GB
At installation to potable water supply plumbers
or users must connect fi rst a safety device
complying with national requirements.
Wall joints must be sealed with non-hardening
joint sealing. The device mus be fl ushed with
water according to DIN 1988. For domestic
installation a dirt trap shall be provided by the
user.
02 Setting up room for shower tray and
shower enclosure
■ The shower ADANA can be installed in the corner.
■ The shower ADANA enclosure has been designed
for installation on bricked walls. Please strenghten
other wall structures (wood, gypsum board), to
ensure a reliable fastening.
■ Please note that in the shower enclosure area
only appropriate materials for wall covering must
be used. A ground surface treatment according to
moisture stress class FKB 2 is required.
■ Before installation the walls must be completely
tiled at the entire cabin hight.
■ The ground surface at the installation location
must be perfectly fl at.
■ A ventilation as well as suffi cient air
dehumidifi cation in the installation room are to
be ensured. If necessary, please apply a suitable
ventilation appliance for water vapour dissipation
in a controllable manner (DIN 18017, DIN 1946
etc.).
⚠
Silicone must be provided by building
constructor. Please keep in mind that
maintenance joints may require cleaning.
4
03 Caring for the steam bath/shower
cabin
After showering/steaming, rinse the tray and wall element
surface with water and wipe down with a damp cloth.
Do not use scouring agents! For occasional thorough
cleaning, use a few drops of cleaning agent, e.g. Hoesch
Cleaner (item no. 699900), on the surface and rub with a
soft, dry cloth. Remove heavier soiling using warm water
and liquid cleaning agent or a soap lye. Wipe away scale
deposits using vinegar and water (avoid contact with the
fittings!). Observe the manufacturer's instructions if using
drain cleaners!
Remove slight scratches or rough areas in glossy surfaces
with the Hoesch Sanicryl care set (item no. 699100,
follow instructions!). Remove deep scratch marks or
burns on glossy or matt surfaces using fi ne sandpaper
(no. 800- 1500) or a fi ne steel wool metal eraser by rubbing
carefully in one direction in a large area around the
scratch. Treat glossy surfaces only with special polishing
cream.
03.01 Caring for the glass panes and profi les
■ After showering, quickly rinse the partition with
clean water.
■ Use only a damp rag (never dry) to wipe down the
panels and frame. You can also use a squeegee
to dry the panels.
■ Only use gentle cleaners such as a weak vinegar
and water solution. Never use cleansing powder
or cleaners containing chlorine.
■ Do not use microfi ber cloths. They destroy any
coatings and may cause the glass to become
scratched.
■ It is a good idea to lightly oil sliding and swinging
doors so they remain easy to open.
03.02 Caring for the fi ttings
For day-to-day cleaning, use neutral or citrus-based
cleaning agents only. Use cleaning agents intended
for cleaning fi ttings only. Follow the instructions for the
cleaning agent!
Spray cleaning agent onto a cloth and use it to clean the
fi ttings.
Rinse the fi tting with plenty of water and polish with a soft
cloth.
03.03 Do not use ...
■ Scouring or scraping cleaning textiles or sponges.
■ Cleaning agents with fl uid acids such as
hydrochloric or citric acid.
■ Scouring agents.
■ Cleaning agents containing chlorine bleach lye.