Taking Weight And Body Fat Readings; Understanding Your Reading; Programming Guest Mode; Taking Weight Measurement Only - Tanita UM-030 Mode D'emploi

GB

TAKING WEIGHT AND BODY FAT READINGS

1. Select Personal Data Number
Press the Up button turn on. Use the Up/Down buttons to select your
Personal data number. Press the Set button to confirm.
(Release the key within 3 seconds or the display will show "Error".)
The unit will beep and the display will show the programmed data.
The unit will beep again and the display will show "0.0".
Now step onto the platform.
Note:
•If you step onto the platform before "0.0" appears the display will show "Error" and you will
not obtain a reading. Furthermore, if you do not step onto the measuring platform within
about 60 seconds after "0.0" appears, the power is shut-off automatically.
•When using the "Up" button to turn the unit on, the personal data number last used will
appear first.
•Numbers that are not pre-programmed are automatically skipped.
2.Get Your Readings
Your weight will be shown first. Continue to stand on the platform.
"00000" will appear on the display and disappear one by one from left to
right.
The readings will be shown alternately 3 times as follows:
Note:Do not step off until Body Fat % is shown.
Weight Body fat percentage

UNDERSTANDING YOUR READING

Healthy Range Indicator (Standard Adults only*)
Your body fat monitor/scale automatically compares your body fat reading to
the Healthy Body Fat Range chart.
Following your body fat percentage reading, a black bar will flash along the
bottom of the display, identifying where you fall within the Body Fat Ranges
for your age and gender. For example, if the squares appear above (0) area
Under Healthy Over Obese
your range is within the Healthy Range – if they appear over (-) area, your
reading is below the Healthy Range. For more about the Healthy Range, see
page 2.
*Note: If you select Athlete mode, the unit will
(-) : Underfat; below the healthy body fat range. Increased risk for health problems.
not display the Healthy Range Indicator. Athletes
(0) : Healthy; within the healthy body fat percentage range for your age/gender.
may have a lower body fat range based on their
(+) : Overfat; above the healthy range. Increased risk for health problems.
particular sport or activity.
(++) : Obese; high above the healthy body fat range. Greatly increased risk
(Range of user age is between 20-79)
7
Total body water percentage
of obesity-related health problems.
PROGRAMMING THE GUEST MODE
Guest mode allows you to programme the unit for a one-time use
without resetting a Personal data number.
Press button to activate the unit. Then follow the
steps: Set Age, Select Female or Male, and Specify Height.
Note : If you step onto the platform before "0.0" appears the display will show "Error"
and you will not obtain a reading.

TAKING WEIGHT MEASUREMENT ONLY

Select Weight-Only Key
Press the Weight-only key. After 2 or 3 seconds, "0.0" will appear in the
display and the unit will beep. When "0.0" appears in the display, step onto
the platform. The body weight value will appear. If you remain on the platform,
the display will flash for about 30 seconds, and then the power will automatically turn off.
If you step off the platform, the weight will continue to show for about 5 seconds, then
"0.0" will appear and the unit will shut off automatically.

TROUBLESHOOTING

If the following problems occur ...then...
• A wrong weight format appears followed by kg, lb, or st-lb
Refer to "Switching the Weight Mode" on p.4.
• "Lo" appears on the display, or all the data appears and immediately
disappears.
Batteries are low. When this message appears, be sure to replace the batteries immediately, since weak batteries will
affect the accuracy of your measurements. Change all the batteries at the same time with new batteries.
Note: Your settings will not be erased from the memory when you remove the batteries.
• "Error" appears while measuring.
Please stand on the platform keeping movement to a minimum.
The unit cannot accurately measure your weight if it detects movement.
• The Body Fat Percentage measurement does not appear or "-----" appears
after the weight is measured.
Your personal data has not been programmed. Follow the steps on p.6.
Make sure socks or stockings are removed, and the soles of your feet are clean and properly aligned with the guides
on the measuring platform.
• "OL" appears while measuring.
Reading cannot be obtained if the weight capacity is exceeded.
• "Error FAT%" appears while measuring.
The Body Fat Percentage is more than 75%, readings cannot be obtained from the unit.
GB
8