Functional Description - Milwaukee 3000 Manuel De L'utilisateur

Support de foret de noyau compact

Masquer les pouces

Table Des Matières

Table des Matières

Les langues disponibles

• Do not expose a battery pack or tool to fire or

excessive temperature. Exposure to fire or temperature

above 265°F (130°C) may cause explosion.

• Follow all charging instructions and do not charge

the battery pack or tool outside the temperature

range specified in the instructions. Charging im-

properly or at temperatures outside the specified range

may damage the battery and increase the risk of fire.

SERVICE

• Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is maintained.

• Never service damaged battery packs. Service

of battery packs should only be performed by the

manufacturer or authorized service providers.

SPECIFIC SAFETY RULES FOR

CORE DRILL STAND

•Hold the power tool by insulated gripping surfaces,

when performing an operation where the cutting

accessory or fasteners may contact hidden wiring.

Cutting accessory or fasteners contacting a "live" wire

may make exposed metal parts of the power tool "live"

and could give the operator an electric shock.

•Always secure the stand to the work surface to help

prevent personal injury and to protect the stand.

Do not rely on the weight of the stand, shoring pin

alone or body weight on the stand for securing

during use. An unsecured stand could rotate during

coring and possibly cause injury. NEVER attempt to

use body weight to hold stand. Never rely on the shor-

ing pin alone for securing.

•When securing the drill stand with anchors and

fasteners to the workpiece, ensure that the anchor-

ing used is capable of holding and restraining the

machine during use. If the workpiece is weak or

porous, the anchor may pull out causing the drill stand

to release from the workpiece.

•When securing the drill stand using the vacuum

gaskets on the workpiece with a vacuum pump,

install the stand on a smooth, clean, non-porous

surface. Do not secure to laminated surfaces such

as tiles and composite coating. If the workpiece is

not smooth, flat or well affixed, the pad may pull away

from the workpiece.

•Ensure there is sufficient vacuum before and dur-

ing drilling. If the vacuum is insufficient, the pad may

release from the workpiece.

•Never perform drilling with the machine secured by the

vacuum pad only, except when drilling downwards. If

the vacuum is lost, the pad will release from the workpiece.

•When drilling through walls or ceilings, protect

persons and the work area on the other side. The

bit may extend through the hole or the core may fall

out on the other side.

•To reduce the risk of injury, always wear proper

eye protection marked to comply with ANSI Z87.1.

•Wear ear protectors when diamond drilling. Exposure

to noise can cause hearing loss.

•

To reduce the risk of injury in ap-

WARNING

plications that produce a consider-

able amount of dust, use an OSHA compliant dust

extraction solution in accordance with the solu-

tion's operating instructions.

•Follow all instructions and warnings provided with

the core drill and accessories. Only use a core drill

and accessories specifically recommended for this tool.

Others may be hazardous.

• Always use common sense and be cautious when

using tools. It is not possible to anticipate every

situation that could result in a dangerous outcome.

Do not use this tool if you do not understand these

operating instructions or you feel the work is beyond

your capability; contact Milwaukee Tool or a trained

professional for additional information or training.

• Maintain labels and nameplates. These carry

important information. If unreadable or missing, contact

a MILWAUKEE service facility for a free replacement.

•

Some dust created by power sanding,

WARNING

sawing, grinding, drilling, and other

construction activities contains chemicals known to

cause cancer, birth defects or other reproductive harm.

Some examples of these chemicals are:

• lead from lead-based paint

• crystalline silica from bricks and cement and other

masonry products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on

how often you do this type of work. To reduce your

exposure to these chemicals: work in a well ventilated

area, and work with approved safety equipment, such

as those dust masks that are specially designed to

filter out microscopic particles.