Télécharger Imprimer la page

Whirlpool WHSS90F Mode D'emploi page 17

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 38
T10. ON/OFF "BREATH DAILY CYCLE"
The hood will automatically set an extraction speed of 1, and then increase it if necessary (according to the ambient conditions
detected by the hood sensor).
If the extraction speed does not change owing to the ambient conditions detected, the hood will switch off after two hours.
The hood will switch off in any case after five hours in use, regardless of the operating mode.
Please note: to make sure this function is used correctly, please configure the parameters for automatic mode first as described in
the relevant section.
T11. ON/OFF "BREATH INTENSIVE CYCLE"
The hood will automatically set an extraction speed of 5, and then increase it if necessary (according to the ambient conditions
detected by the hood sensor).
If the extraction speed does not change owing to the ambient conditions detected, the hood will switch off after two hours.
The hood will switch off in any case after five hours in use, regardless of the operating mode.
Please note: to make sure this function is used correctly, please configure the parameters for automatic mode first as described in
the relevant section.
T12. LIGHT INDICATOR FOR WI-FI FUNCTION ACTIVE
The indicator comes on when the hood is controlled from a distance via the app.
T13. WI-FI CONNECTION
Press to activate/deactivate the WI-FI functions.
This function allows the hood to be connected to the Internet so you can monitor/control it from a distance via a smartphone or tablet.
To use the WI-FI function, connect the appliance to the domestic wireless network (Internet) following the configuration procedure
explained in the "WI-FI MANUAL".
CONFIGURING THE PARAMETERS FOR AUTOMATIC MODE
To make sure that automatic mode is used correctly, you will need to calibrate the hood and select the hob type.
Calibrating the hood
NB: this must be done with the appliance on standby - i.e. one minute after switching off the motor.
Press and hold the T4 button for five seconds.
Extraction speed 1 will be activated and the T4 button will flash to indicate that hood calibration has started (this will take approx. 5
minutes).
Please note: To stop the calibration process, press and hold the T4button for five seconds. Calibration will then be invalidated and
will therefore need to be repeated.
Please note: Calibration will be carried out automatically when the power supply to the product is switched on for the first time. T4
will flash. Wait 5 minutes for the calibration to be completed.
Selecting the hob type
NB: this must be done with the appliance on standby - i.e. one minute after switching off the motor.
Press and hold the T10 and T11 buttons for five seconds.
The T10 and T11 buttons will light up.
If using gas to power the hob, press the T10 button – the button will flash to indicate that this has been selected.
If using electricity to power the hob, press the T11 button – the button will flash to indicate that this has been selected.
Once pressed, the button will flash for three seconds to indicate that your selection has been saved.
WI-FI MANUAL
LIVE APPLICATION REMOTE CONTROL /SET UP PROCEDURE
The LIVE feature allows to operate and supervise the appliance remotely by external device. To enable the appliance to be remotely
controlled, you first have to complete successfully the connectivity set up process. This process is necessary to register your
appliance and connect to your home network. The set up procedure has to be carried out only once. You have to carry it out again if
you change your router set up properties (network name or password or data provider).
1.1 BEFORE STARTING THE SET UP PROCESS
1.
To use this feature You need to own: • a smart phone running Android 4.3 (or higher) with a 1280x720 (or higher) screen or a
tablet or a smart phone running iOS 8 (or higher); • a wireless router 2.4Ghz WiFi b/g/n connected to internet (verify with your
smart device that the signal strength of your home wireless network close to the appliance is good).
2.
Download & Install the free application: LIVE on your Android smart-phone or iPAD/iPhone from the store. The App will guide
17

Publicité

loading