Milwaukee MXF500 Manuel De L'utilisateur page 9

NOTE: If more cable is needed to reach the clog,
disconnect the original cable from the anchor cable.
Then, either load additional cable into the machine
and connect the two cables together, or connect
the original cable to the cable in another machine.
WARNING! Never feed more than 100' of cable into
the machine to avoid overloading.
6. When the clog is reached, disengage the auto
feed. Manually move the cable in a back and
forth motion until the obstruction is cleared. If the
machine binds, release pressure from the foot
pedal immediately. Repeat until the drain is clear.
To Unbind Cable in the Drain
To relieve torque (twisting) on the cable:
1. Disengage the cable feed.
2. Move the Forward/OFF/Reverse switch to
Reverse and pulse the foot pedal once to begin
rotating the cable. Do not hold down the foot
pedal.
3. Pull the cable back out from the drain a few inches
to free the cable.
4. After the cable is freed from the obstruction and
the machine has come to a complete stop, switch
back to Forward
struction.
Running the machine in Reverse for
CAUTION
extended periods can cause damage
to the cable and accessories.
Removing Cable From Drain
1. Move the Forward/OFF/Reverse switch to
Forward and press the foot pedal to begin rotat-
ing the cable.
2. Pull the cable away from the drain and feed it into
the drum. Use the cable feed in "retract" if desired.
3. As the working end of the cable is neared, feed
the last 5' of cable into the machine by hand.
Do not use cable feed. WARNING! Never feed
more than 100' of cable into the machine to avoid
overloading.
4. Remove the drum plug and drain into a suitable
location.
5. Before storing the machine, wash the cable and
drum (see "Cleaning Cables and Drum" in Main-
tenance).
MAINTENANCE
To reduce the risk of injury, always
WARNING
unplug the charger and remove the
battery pack from the charger or machine before
performing any maintenance. Never disassemble
the machine, battery pack or charger. Contact a
MILWAUKEE service facility for ALL repairs.
Maintaining Machine
Keep your machine, battery pack and charger in good
repair by adopting a regular maintenance program.
Inspect your machine for issues such as undue noise,
misalignment or binding of moving parts, breakage
of parts, or any other condition that may affect the
machine operation. Return the machine, battery
pack, and charger to a MILWAUKEE service facility
for repair. After six months to one year, depending on
use, return the machine, battery pack and charger to
a MILWAUKEE service facility for inspection.
If the machine does not start or operate at full power
with a fully charged battery pack, clean the contacts
on the battery pack. If the machine still does not work
properly, return the machine, charger and battery
pack, to a MILWAUKEE service facility for repairs.
and continue working the ob-
ONE-KEY™
Chemical Burn Hazard.
WARNING
This device contains a
lithium button/coin cell battery. A new
or used battery can cause severe in-
ternal burns and lead to death in as
little as 2 hours if swallowed or enters the body.
Always secure the battery cover. If it does not
close securely, stop using the device, remove the
batteries, and keep it away from children. If you
think batteries may have been swallowed or en-
tered the body, seek immediate medical attention.
Internal Battery
An internal battery is used to facilitate full ONE-KEY™
functionality.
If the Bluetooth communication stops working,
®
remove and reinsert the coin cell battery to reset.
Replace the battery if the problem continues.
To replace the battery:
1. Remove the battery pack.
2. Remove the screw(s) and open the battery door.
3. Remove the old battery. Take note of the positive/
negative orientation. WARNING! Keep battery
away from children, and dispose of it properly.
4. Insert the new battery (3V CR2032) in the proper
positive/negative orientation.
5. Close the battery door and tighten the screw(s)
securely.
To reduce the risk of personal in-
WARNING
jury, electric shock and damage,
never immerse your machine in liquid or allow a
liquid to flow inside it.
Clean dust and debris from vents. Keep handles
clean, dry and free of oil or grease. Use only mild
soap and a damp cloth to clean, since certain clean-
ing agents and solvents are harmful to plastics and
other insulated parts. Some of these include gasoline,
turpentine, lacquer thinner, paint thinner, chlorinated
cleaning solvents, ammonia and household deter-
gents containing ammonia. Never use flammable or
combustible solvents around machines.
Greasing the Cable Feed
Apply grease to the cable feed after each use.
1. Unarm the machine.
2. Press the quick release
button.
3. Push the cable feed handle
to the left side of the ma-
chine.
4. Apply MILWAUKEE Grease
Type T (49-08-4290) to
the upper Zerk fitting, suf-
ficiently covering the fitting.
5. Press the cable feed ratchet
lever down.
6. Push the cable feed handle to the right side of
the machine.
7. Apply MILWAUKEE Grease Type T (49-08-4290)
to the two lower Zerk fittings, sufficiently covering
the fittings.
9
Cleaning
Zerk Fittings