Goobay 45284 Mode D'emploi page 3

Betriebsanleitung | User manual | Mode d'emploi
Standventilator DE | EN | FR | IT | ES
Not meant for children. The product is not a toy!
• Secure packaging, small parts and insulation against accidental use.
• Do not insert any fingers or objects through the protective net. This
can lead to injuries or damages to the device.
• Keep long hair and loose clothing away from the fan. These can be
sucked in by the air flow.
• Make sure that the fan is not near curtains or objects that can be
pulled into the fan.
• Do not operate the fan in the vicinity of explosive and/or flammable
gases.
• Do not place or operate the product near open flames, cooking or heat
generating products such as radiators, heating registers and stoves.
• Do not keep limbs between shearing parts.
• Do not hold limbs between shears.
• NEVER leave the product unattended during operation.
• Risk of injury from moving product parts.
Risk of injury due to tripping and falling
Operation and storage conditions
• Place, install and transport product, product parts and accessories in a
safe way.
• During operation, place the product on a stable, level, dry and dust-
free surface so that it does not tilt during operation and the floor
covering cannot be damaged by vibrations.
• Avoid stresses such as heat and cold, moisture and direct sunlight,
microwaves, vibrations and mechanical pressure.
• Immediately disconnect the power plug if the product has become
damp or wet.
• Do not operate the product in dusty environments or with inadequate
ventilation.
• Do not cover the product.
• Keep fan slots and vents free.
• NEVER leave unattended while in operation.
• Switch off the device and disconnect the product from the mains when
not in use, when accessories are attached, for cleaning or in the event
of a fault.
Target group information
Caused to different risk levels and hazard potentials some working
steps only may be done by trained specialists:
Working step User Group
Installing, operating, care, storage, Consumers and users with basical
transport, disposal mechanical knowledge can do this work.
Dissembly, maintenance, repairing Trained specialists only >> special safety
measures, knowledge and tools are
necessary!
Not recommended for children and people with physical and / or
mentally limited capabilities.
Description and Function
pedestal fan
pedestal fan provides a pleasant refreshment on hot days.
• 3 speed levels: low, medium and high
REV2019-10-18
V1.0CS
Änderungen vorbehalten. | Subject to change without notice. | Sous réserve de modifications.
• practical, space-saving and modern design
• very quiet electric motor
Specifications
Model
Inputvoltage 220-240 V @ 50/60 Hz
Power (W)
Standby power consumption
Max. volume flow (m³/min)
Service value (m³/min) / W
Max. air velocity (m/s)
Sound power level (dBA)
Protection level / Protection class
Colour
Dimensions
B x H x T (cm)
Ø (cm)
Net weight (g)
Device connection Euro male (Type C, CEE 7/16)
Cable length [m]
Scope of delivery
1. Grid clamping ring 2. Front part of grid
3. Fan fastener 4. Fan
5. Grid fastener 6.Back part of grid
7. Motor 8.Control panel
9. Rotation regulator 10.Fixing bolt
11. Height adjusting part of stand 12.Strainer ring
13. Bottom oft he stand [to be fastened] 14. Cover Piece
15. Base 16. Manual
Intended Use
This product is intended exclusively for private use and its
intended
commercial use. We do not
45284
other ways like described in chapter "Description and Function" and
„Safety Instructions". Use the product only in dry interior rooms. Not
45
attending to these regulations and safety instructions might cause fatal
-
accidents, injuries, and damages to persons and property.
60.98
IPX0: This product is not protected against water.
1.388
3.25
56 Preparation
• Check the scope of delivery for completeness and integrity.
IPX0 / II
white • Compare the specifications of product, power supply and peripherals.
65x130x65
These must be identical.
40
• Safely place, install and transport product, product parts and
accessories.
2590
Mounting the fan
1,6
1. remove the packaging carefully, avoid scratches on the
packaging the plastic cover with scissors or knife.
2. Attach the rear grille[6] to the motor[7].
3. Then fit the protective ring[5].
4. Place the blade on the shaft[4] and fix it with the blade
holder.
5. Attach the front guard[2] to the fan with the protective ring[1]
and tighten it with a screw to secure it.
6. Mount the stand as follows and adjust the fan on it!
Mounting the stand
1. Connect the two parts of the base[15].
2. Attach the bottom of the stand to the base[15] by tightening
the screws! Then place the cover piece on top!
3. adjust the desired height of the stand and fasten it with the
sieve ring[12]!
4. now place the mounted cooling fan unit on it and fasten
them with the bolt!
Operating
• Make sure the ventilator has a firm footing. The fan must not stand on
the power cord to prevent it from tipping over during operation.
• Turn the front of the fan in the direction you want to ventilate.
Setting up
• Mind placing cables in a way, nobody will be disabled and the cable
not be damaged.
• Install the system and devices attached to it in a way that persons
cannot be injured, or objects not be damaged for example by drop-
ping or stumbling.
• Connect the ventilator to a protective contact socket.
purpose. This product is not intended for
permit using the device in
Goobay® | by Wentronic GmbH
Pillmannstraße 12 | 38112 Braunschweig
Germany