Jata Beauty MP373N Manuel D'utilisation page 13

• In order to optimise the durability of the battery bear in mind the following pieces of advice:
-Never exceed the indicated loading times for the battery.
-It is important to discharge the battery before it is recharged, leave it on until it stops or the power decreases clearly.
-The battery must be recharged every 6 months if it has not been used for said period of time.
-Also recharge if it has not been used for more then a month.
LUBRIFICATION
• For the hair clippers to work correctly it is absolutely necessary to lubricate the blades with oil before each
use.
• Carefully pour a few drops of oil, which is provided, between the teeth of the blade, or if you have run out, with another
high quality, acid free oil.
• Turn the hair clippers on for a few seconds and clean the excess oil off with a cloth.
CUTTING GUIDE POSITIONS
• The unit is equipped with three practical cutting guides, which allow a precise adjustment of the desired length.
1.Precision cutting guide:
This guide allows a cutting height between 0,5 and 2,5 mm. Once inserted the guide slide the regulator (2) placed in the
lower part to leave it in the desired position. The different positions are showed under the comb.
Position with the closed comb. Cutting height of 0.5 mm.
Position 1. Cutting height of 1 mm.
Position 2. Cutting height of 1.5 mm.
Position 3. Cutting height of 2 mm.
Position 4. Cutting height of 2.5 mm
2.Cutting guide 3-18 mm. To cut between 3 and 18 mm. The guide has this indications in both sides.
3.Cutting guide 21-36 mm. To cut between 21 and 36 mm. The guide has this indications in both sides.
• To assemble the chosen guide place it in the blade and press the bottom flange of the guide to be inserted. (fig. A)
• To insert the guides of 3-18 and 21-36 mm. in the desired position, place the fixing button (11) in the position (
Next turn forwards the regulator (8) to leave it in the desired position. The indications of the cutting guide of 3-18 mm
are placed in the left side of the unit. The indications of the cutting guide of 21-36 mm are in the right side of the unit.
• Next and before starting, place the fixation button in the (
BEGINNING THE CUT
• Relax and work slowly. Make short cuts. Do not go on to the final cut of one side or the back straight away. Work gradually
and all over the head.
• It is better to cut a little each time to be able to cut some more later on.
• While you are working and before you begin, comb the hair frequently to the chosen style.
• It is preferable to cut the hair when it is dry, not wet. It is easier to see and control the amount of hair you are cutting.
• The first time you use the appliance it is advisable to cut a small portion of hair until you get used to the lengths of the
different positions of the guide. At the beginning use the guides with the longest cutting length. With a little practice
you will soon choose the most adequate position for the length you wish to have.
• After combing your hair following its natural direction, proceed as follows to obtain a perfect hair cut.
First step: NAPE
• Place the guide in around 4 mm. cutting position. Start cutting at the centre of the nape and at the bottom of the neck.
Hold the hair clippers softly against the head with the teeth of the guide pointing upwards.
• Go up gradually, working your way upwards and outwards, just cutting a little hair at a time. When cutting raise the head
of the clippers towards you little by little. Continue cutting at the back of the head from the base of nape to the area
just above the ears (Zone "A", photo 1).
Second step: THE BACK OF THE HEAD
Set the guide in approximately 8-10 mm. and cut the area at the back of the head, identified as zone "B" on photo 2.
Third step: SIDES
• With the guide set in around 4-7 mm. cutting position, start cutting the side burns and the area close to the ears. Next,
set the guide to a higher position to go on cutting the hair at the top of the head.
) position to leave it fixed.
13
).