Legend; Safety Precautions; Operating Instructions - EUFAB 16542 Manuel De L'opérateur

LEGEND

Complies with EC directives
Protective insulation
(safety class II)
Mains transformer - not short-circuit proof
Output voltage to max. 50 Volt

SAFETY PRECAUTIONS

The warning triangle labels all instructions relevant for safety. Always comply with these, as non-observance may lead to injuries or damage
the device.
Only connect the device to a power socket installed according to regulations. The voltage has to correspond with the information on the type
plate of the device.
Do not pinch the mains cable and protect it from sharp edges, humidity, heat or oil. The mains cable cannot be replaced. The device has to be
scrapped if the cable is damaged.
Do not operate the device or pull the mains plug immediately if the cable is damaged or in the event of a suspected defect. In these cases, please
contact our technicians.
Pull the mains plug when the device is not being operated.
Keep the packaging material, particularly fi lms and fi lm bags out of reach of children. Risk of suff ocation.
Remove all protective fi lms from the device prior to start-up.
Place the mains cable in such a manner that it does not impede and that it cannot be unplugged accidentally.
Disconnect the battery charger from the power supply after the charging process.
Store the charger in a place which is out of the reach of children and unauthorised persons.
Do not operate the device close to combustible material or in an explosive environment.
Always wear suitable work clothing, protective gloves and safety glasses. Battery acid is caustic! Immediately rinse any acid splashes with lots
of water and consult a physician, if required. If battery acid has come in contact with eyes, rinse immediately under running water for at least
10 minutes and consult a physician.
Do not cover the charger as this may lead to overheating and thus damage to the device. During operation, do not place the charger on an
insulating surface (e.g. polystyrene) - risk of heat accumulation!
If you would like to charge a motor vehicle battery in an in-situ position, fi rst park the vehicle securely, then pull the parking break and switch
off the engine. Disconnect the battery from the electrical distribution system of your vehicle. For this purpose, read the manual of your vehicle
or ask your specialist workshop.
Only hold the power cable at the power plug when disconnecting from the power socket.
Do not expose the charger to fi re, heat and long-temperature impact of more than +40°C!
Keep these operating instructions and pass them on to other users.

OPERATING INSTRUCTIONS

Preparation of the battery
Clean the battery poles from dust and corrosion residue. Only for open batteries: replenish distilled water up to the minimum fi ll level. Leave the cells of the
battery open until the end of the charging process. In case of maintenance-free batteries, please follow the instructions of the battery manufacturer to the
letter.
Connecting of battery charger
ATTENTION
Ensure that the charger is not connected to the power socket. Principally connect the red positive cable (+) of the charger to the positive pole of
the battery fi rst. Subsequently, connect the black minus cable (-) to the negative pole of the battery. If you charge the battery in situ, connect
the black negative cable (-) to the car body, far away from the battery, the carburettor and fuel lines. Always maintain this sequence.
Protection from connection to the wrong pole
The device is equipped with a fuse in order to protect the user from injury and the device from damage in case of accidental connection to the wrong poles. In
the event of a wrong connection, this fuse is activated and subsequently requires a replacement with a fuse of the same type. This fuse is located in a bracket
at the bottom of the device.
Charging of battery
Now, connect the power plug of the charger to the mains socket. The charging process has now started and the control LED „LADEN" (CHARGING) lights up.
The charging time of the battery depends on several factors, such as the capacity of the battery, the ambient temperature, the battery level, the performance
of the charger, etc. An empty 36 Ah battery, at an ambient temperature of 20 °C, is fully loaded with this device in approx. 9 hours. It is very important to
monitor the charging process in short intervals in order to prevent overcharge damages. Finish the charging process when the control LED „VOLL" (FULL) is lit
up by pulling the mains cable of the battery charger from the mains socket.
Labelled electrical products may not be
disposed of in household garbage
Fuse, here: 7.5 A
Devices with this label may only be
operated inside (dry environment)
Read operating instructions
5