Télécharger Imprimer la page

Federal Signal Corporation EMS Escape Instructions D'installation Et D'entretien page 2

Publicité

Les langues disponibles

Les langues disponibles

SAFETY MESSAGE TO INSTALLERS
FEDERAL SIGNAL LIGHT SYSTEMS
People's lives depend on your safe installa-
tion of our products. It is important to read,
understand and follow all instructions
shipped with the products. In addition, listed
below are some other important safety
instructions and precautions you should
follow:
To properly install a light assembly: you
must have a good understanding of
automotive electrical procedures and
systems, along with proficiency in the
installation and use of safety warning
equipment.
When drilling into a vehicle structure, be
sure that both sides of the surface are
clear of anything that could be damaged.
A light system is a high current device. In
order for it to function properly, a sepa-
rate ground connection must be made. If
practical, it should be connected to the
negative battery terminal. At a minimum,
it may be attached to a solid metal body
or chassis part that will provide an
effective ground path as long as the light
system is to be used.
Locate light system controls so the
VEHICLE and CONTROLS can be oper-
ated safely under all driving conditions.
This product contains high intensity LED
devices. To prevent permanent eye
damage, DO NOT stare into the light
beam at close range.
You should frequently inspect the light
system to ensure that it is operating
properly and that it is securely attached
to the vehicle.
File these instructions in a safe place and
refer to them when maintaining and/or
re-installing the product.
Failure to follow all safety precautions and
instructions may result in property damage, serious
injury, or death to you or others.
I.
GENERAL.
This instruction sheet provides directions for installa-
tion, and maintenance of the EMS Escape lightbar. The
EMS Escape lightbar is designed to mount on the vertical
surface of vehicles. Typical applications would include
INSTALLATION AND MAINTENANCE INSTRUCTIONS
EMS ESCAPE™ LIGHT BARS
OF
WARNING
FOR
ambulance, fire, and rescue bodies. The EMS Escape
lightbar may be mounted direct or via the Quick Track™
mounting system to the vehicle's surface.
II.
UNPACKING.
After unpacking the light bar, inspect it for damage
that may have occurred in transit. If the unit has been
damaged, file a claim immediately with the carrier, stating
the extent of damage. Carefully check all envelopes,
shipping labels and tags before removing or destroying
them. Ensure that all parts listed in the Kit Contents List
are included in the package.
Kit Contents List
Qty.
Description
4
3/8-16 x 2", Carriage Bolt, S.S.
8
M8 x 25mm, Set Screw w/Nylok, S.S. 7008039A
4
3/8 Flat Washer, S.S.
4
3/8 Lockwasher, S.S.
4
3/8-16 Hex Nut, S.S.
2
Mounting Strip Gasket (10')
1
Grommet, Seal
2
Carriage, Seal
III. INSTALLATION.
The EMS Escape light bar is completely wired at the
factory and does not require any additional internal wiring.
All the conductors necessary for control of any and all basic
and optional functions are contained in the supplied
cable(s). Installation of options will require additional
wiring in the light bar.
The basic light functions of the unit must be controlled
by a user-supplied control head.
Light system controls must be located so that
VEHICLE and CONTROLS can be operated
safely under all driving conditions.
When installing equipment inside air bag
equipped vehicles, the installer MUST ensure
that the equipment is installed ONLY in areas
recommended by the vehicle manufacturer.
Failure to observe this warning will reduce
the effectiveness of the air bag, damage the
air bag, or potentially damage or dislodge the
equipment, causing serious injury or death to
you or others.
The EMS Escape lightbar is designed for mounting
directly to the vehicle's surface or via the Quick Track
mounting system. The direct mounting method incorpo-
rates carriage bolts, washers, lockwashers, and nuts to
provide a secure and somewhat permanent installation,
unless provisions for future removal are made during the
assembly of your vehicle.
-1-
Part No.
7004A024-32
7072A035
7074A046
7059A063
8003006A
8003127A
8003128A
WARNING
WARNING

Publicité

loading

Produits Connexes pour Federal Signal Corporation EMS Escape

Ce manuel est également adapté pour:

Quick track