SilverCrest 837800 Mode D'emploi page 6

GB
Product Familiarisation
1 Lock On/Off Button
2 Insulated Handle
3 Trigger
4 Magazine Release
5 Magazine Window
6 Firing Point
Intended Use
Hand-held portable mains powered nailer/stapler for light duty use. Suitable for a
wide range of materials of medium to low density. Not suitable for the majority of
metals or ceramics or other dense materials
Unpacking Your Tool
Carefully unpack and inspect your tool. Familiarise yourself with all its features
and functions.
Ensure that all parts of the tool are present and in good condition. If any parts are
missing or damaged, have such parts replaced before attempting to use this tool.
Before Use
WARNING: Always disconnect from the power supply before carrying out any
maintenance/cleaning.
Loading the magazine
1. Ensure that the stapler is disconnected from the mains power supply
2. Press down on the Magazine Release (4) and pull open the magazine as
shown in image Fig. I
3. Insert staples into the magazine as shown in Fig. I or nails as shown
in Fig. II, ensuring the point of the fastener is facing downwards (away
from the Insulated Handle (2) of the tool). See specification for suitable
fasteners. Ensure nails are on the correct side as shown and indicated by
the symbol on the base of the magazine
4. Close the magazine, ensuring the Magazine Release (4) clicks shut
Note: The Magazine Window (5) provides a quick indication of how close the tool is
to running out of fasteners
Operation
Connection to power
1. Depress the Lock On/Off Button (1) to lock the Trigger (3) off and prevent
use
2. Insert the mains plug into the mains outlet and switch the mains socket
on (UK only)
3. To switch off after use remove the mains plug from the mains socket
Firing staples and nails
1. Move the Lock On/Off Button (1) to the unlocked position by depressing
the button on the opposite side to the one shown
2. Always hold the tool securely. Grip the Insulated Handle (2) with one
hand, and place the other hand on the top of the body of the tool at
the rear where the insulated material is fitted. This will give you
maximum control of the tool. It is also safe to use the tool single-handed
when securing a workpiece or material with the other hand
3. Hold the tool firmly against the material
4. Gently squeeze the Trigger (3) until the fastener is fired
5. Release the trigger and check that the fastener has penetrated the
material correctly.
Note: If the fastener fails to penetrate correctly it is possible the material is too
dense and not suitable for the tool
Clearing jams
1. Disconnect the stapler from the mains power supply
2. Depress the Magazine Release (4) and open the magazine
3. Remove the obstruction using pliers
4. Reload the magazine and close securely
6
Accessories
A range of staples and nails are available for this power tool from your Silverline
dealer. The following length Silverline staples are available; 8mm (101722), 10mm
(101729), 12mm (101732) and 14mm (101739). Spare parts are available from
your Silverline dealer or www.toolsparesonline.com.
Maintenance
WARNING: Always disconnect from the power supply before carrying out any
maintenance/cleaning.
• Inspect the supply cord of the tool, prior to each use, for damage or wear. This
advice also applies to extension cords used with this tool
• If replacement of the supply cord is necessary, this has to be carried out by the
manufacturer or his agent in order to avoid a safety hazard.
Lubrication
• Lubricate all moving parts with a suitable lubricant spray, at regular intervals
Cleaning
WARNING: ALWAYS wear protective equipment including eye protection and gloves
when cleaning this tool.
• Keep your tool clean at all times. Dirt and dust will cause internal parts to wear
quickly, and shorten the device's service life
• Clean the body of your machine with a soft brush, or dry cloth
• Never use caustic agents to clean plastic parts. If dry cleaning is not sufficient, a
mild detergent on a damp cloth is recommended
• Water must never come into contact with the tool
• Ensure the tool is thoroughly dry before using it
Storage
• Store this tool carefully in a secure, dry place out of the reach of children
Disposal
Always adhere to national regulations when disposing of power tools that are no
longer functional and are not viable for repair.
• Do not dispose of power tools, or other waste electrical and electronic
equipment (WEEE), with household waste
• Contact your local waste disposal authority for information on the correct way
to dispose of power tools