Publicité
Les langues disponibles
Les langues disponibles
837800
General Safety
WARNING Read all safety warnings and all instructions. Failure to follow the
warnings and instructions may result in electric shock, fire and/or serious injury.
WARNING: This appliance is not intended for use by persons (including
children) with reduced, physical or mental capabilities or lack of experience
or knowledge unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
Children must be supervised to ensure that they do not play with the appliance.
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your mains-operated (corded)
power tool or battery-operated (cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas invite
accidents.
b) Do not operate power tools in explosive atmospheres, such as in
the presence of flammable liquids, gases or dust. Power tools create
sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in
any way. Do not use any adapter plugs with earthed (grounded)
power tools. Unmodified plugs and matching outlets will reduce risk of
electric shock.
b) Avoid body contact with earthed or grounded surfaces, such as
pipes, radiators, ranges and refrigerators. There is an increased risk
of electric shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a
power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling
or unplugging the power tool. Keep cord away from heat, oil, sharp
edges or moving parts. Damaged or entangled cords increase the risk
of electric shock.
e) When operating a power tool outdoors, use an extension cord
suitable for outdoor use. Use of a cord suitable for outdoor use reduces
the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable, use
a residual current device (RCD) protected supply. Use of an RCD
reduces the risk of electric shock.
g) When used in Australia or New Zealand, it is recommended that this
tool is ALWAYS supplied via Residual Current Device (RCD) with a rated
residual current of 30mA or less.
3) Personal safety
a) Stay alert, watch what you are doing and use common sense when
operating a power tool. Do not use a power tool while you are tired
or under the influence of drugs, alcohol or medication. A moment
of inattention while operating power tools may result in serious personal
injury.
b) Use personal protective equipment. Always wear eye protection.
Protective equipment such as dust mask, non-skid safety shoes, hard
hat, or hearing protection used for appropriate conditions will reduce
personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off-
position before connecting to power source and/or battery pack,
picking up or carrying the tool. Carrying power tools with your finger
on the switch or energising power tools that have the switch on invites
accidents.
d) Remove any adjusting key or wrench before turning the power tool
on. A wrench or a key left attached to a rotating part of the power tool
may result in personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This
enables better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your
hair, clothing and gloves away from moving parts. Loose clothes,
jewellery or long hair can be caught in moving parts.
g) If devices are provided for the connection of dust extraction and
collection facilities, ensure these are connected and properly used.
Use of dust collection can reduce dust-related hazards.
45W Compact Corded Nailer/Stapler 15mm
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer at the
rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off.
Any power tool that cannot be controlled with the switch is dangerous
and must be repaired.
c) Disconnect the plug from the power source and/or the battery
pack from the power tool before making any adjustments, changing
accessories, or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow
persons unfamiliar with the power tool or these instructions to
operate the power tool. Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools. Check for misalignment or binding of moving
parts, breakage of parts and any other condition that may affect
the power tool's operation. If damaged, have the power tool
repaired before use. Many accidents are caused by poorly maintained
power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools
with sharp cutting edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc. in accordance
with these instructions, taking into account the working conditions
and the work to be performed. Use of the power tool for operations
different from those intended could result in a hazardous situation.
5) Service
a) Have your power tool serviced by a qualified repair person using
only identical replacement parts. This will ensure that the safety of the
power tool is maintained.
Nailer Stapler Safety
WARNING: Always wear eye protection when operating a nailer or stapler.
• Hold power tool by insulated gripping surfaces, when performing an
operation where the nail or staple may contact hidden wiring or its own
cord. Contacting a "live" wire may result in exposed metal parts of the power
tool becoming "live" and could give the operator an electric shock
• Always assume that the tool contains fasteners. Careless handling of the
tool can result in unexpected firing of fasteners and could cause personal injury
• Do not attempt to fire into material of similar hard density to the nails and
staples. This can cause personal injury and damage to the tool
• Ensure built-in safety devices are enabled and operating correctly. Never
disable a built-in safety device
• Do not activate the tool unless the tool is placed firmly against the
workpiece. If the tool is not in contact with the workpiece, the fastener may be
deflected away from the target
• If operating the tool causes discomfort in any way stop immediately.
Review your method of use and allow a rest period before continuing
• Always keep hands clear of the workpiece when using the nailer stapler.
Staples may cause serious injury if fired accidentally
• Always disconnect the nailer stapler from the power supply before
reloading staples or nails
• Never point the tool at persons or animals. Staples or nails fired, even from a
distance, can cause significant injuries
• Always position the nailer stapler at 90˚ to the work surface. Firing at the
wrong angle may cause staples or nails to ricochet back towards the operator
• Ensure that the workpiece is adequately sturdy to stop the staple. In some
situations it may be possible for a staple or nail to pass through a workpiece
• Do not attempt to fire staples or nails over existing fixings
• Do not fire staples or nails close to the edge of a workpiece. Small pieces
may split off and could cause injury
• Do not use the tool to fasten electrical wiring. Contact with electric current
can lead to fire and/or electric shock
www.silverlinetools.com
5
Publicité
