Remote Control; Care And Cleaning - Global Industrial 292855 Manuel De L'utilisateur

7. Sleep Button: Press the SLEEP button. The Sleep Light
will be on after , and all the remaining lights will be off.
In SLEEP mode, the air conditioner will automatically
adjust the temperature and fan speed to make the room
more comfortable during the evening. For cooling mode,
the set temperature will automatically raise by 1ºF or 2ºF
every 30-60 minutes and at most change six times until
the set temperature is 82ºF. For heating mode, the set
temperature will automatically decrease by 1ºF or 2ºF
every 30-60 minutes and at most change six times until
the set temperature is 75ºF. Every running time depends
on the set temperature.
8. Fan Speed Button: Press the FAN SPEED button to
choose the fan speed options. You can choose Hi, Med,
Lo or Auto speed in COOL mode and choose Hi, Med,
Lo in FAN mode.

REMOTE CONTROL

1
3
4
5
6
3
For number 6 button, AUTO MODE is for cooling
only, it would be marked HEAT for heating model.
Inserting or Replacing the Batteries
• Remove the cover on the rear of the remote control.
• Insert two AAA 1.5V batteries in the correct position
(see instructions inside the battery compartment).
Note:
• If the remote control unit is replaced or disposed
of, the batteries must be removed and discarded in
accordance with current legislation as they are harmful
to the environment.
• Do not mix old and new batteries. Do not mix
alkaline, standard (carbon-zinc) or rechargeable
(nickel-cadmium) batteries.
• Batteries may explode or leak if exposed to open
flames. Dispose of batteries accordingly.
• If the remote control is not being used for extended
periods of time (winter storage), remove the batteries
and store in a cool, dry location.
For mode functionality details see page 4
Through The Wall
Air Conditioner
9. Filter Button: When the Filter Check light is off, When
the Filter Check light is on, the light by pressing the
Filter Check button. After the fan motor works for 500
total hours, the Filter Check light will turn on to remind
the user to clean the filter. it isn't necessary to press the
Filter Check button. you can turn off.
10. Directional Louvres: To direct the airflow, use the
horizontal wheel to control the horizontal direction and
the air deflector to control the vertical direction.
Fig. 8

CARE AND CLEANING

Clean your air conditioner to keep it looking new and to
minimize dust build up.
Air Filter Cleaning
The air filter should be checked once a month to see if it
2
requires maintenance. Trapped particles and dust can build
up in the filter and may decrease airflow as well as cause
the cooling coils to accumulate frost. To clean the air filter.
1. Remove the filter by pulling down on the in dents of the
7
filter door on the front of the unit. (Fig 9)
2. Wash the filter using liquid dish soap and warm water.
8
Rinse the filter thoroughly. Gently shake the filter to
9
remove excess water.
10
3. Let the filter dry completely before placing it into the
air conditioner.
4. If you do not wish to wash the filter, you may vacuum the
filter to remove the dust and other particles.
Wear and Tear
To minimize wear and tear on the air condi tioner, wait at
least 3 minutes before changing modes. This will help
prevent the compressor from overheating and the circuit
breaker from tripping.
Cabinet Cleaning
To clean the air conditioner cabinet:
• Unplug the air conditioner to prevent shock or a fire hazard.
The cabinet and front panel may be dusted with an oil free
cloth or washed with a cloth dampened in a solution of
warm water and mild liquid soap. Rinse thoroughly with a
damp cloth and wipe dry.
• Never use harsh cleaners, wax or polish on the cabinet front.
• Be sure to wring excess water from the cloth before
wiping around the controls. Excess water in or around the
controls may cause damage to the air conditioner.
5
Air Deflector Horizontal Wheel
User's Manual
Air Deflector
Fig. 9