Inserting The Battery; Replacing The Battery; Manual Setting - Hama PG-300 Mode D'emploi

G Operating instruction
Controls and Displays
1. SET button
2. RESET button
3. WAVE button
4. Battery compartment
5. Thermometer display (°C on outer scale/°F on inner scale)
6. Hygrometer display
1. Explanation of Warning Symbols and Notes
Warning
This symbol is used to indicate safety instructions or to draw your
attention to speci c hazards and risks.
Note
This symbol is used to indicate additional information or important notes.
2. Package Contents
• Radio Controlled DCF Wall Clock
• 1 AA battery
• These operating instructions
3. Safety Notes
• Protect the product from dirt, moisture and overheating, and only use it in
a dry environment.
• Do not use the product in areas where the use of electronic devices is not
permitted.
• Do not drop the product and do not expose it to any major shocks.
• Do not put the product near interference elds, metal frames, computers,
TVs, etc. Electronic devices and window frames can negatively affect the
product's functionality.
• Do not modify the product in any way. Doing so voids the warranty.
• Keep the packaging material out of the reach of children due to the risk
of suffocation.
• Dispose of packaging material immediately according to locally applicable
regulations.
Warning – Batteries
• Immediately remove and dispose of dead batteries from the product.
• Only use batteries (or rechargeable batteries) that match the speci ed
type.
• When inserting batteries, note the correct polarity
(+ and - markings) and insert the batteries accordingly. Failure to do so
could result in the batteries leaking or exploding.
• Do not overcharge batteries.
• Keep batteries out of the reach of children.
• Do not short circuit the batteries/rechargeable batteries and keep them
away from uncoated metal objects.
4. Getting Started

4.1 Inserting the battery

Remove the battery that was already inserted into the clock, remove the
protective lm if necessary as well as the contact interrupter and the re-insert
the battery with the correct polarity. The clock is ready for operation.

4.2. Replacing the battery

• Remove and dispose of any used batteries. Insert the new battery (AA).
• Ensure that the polarity of the battery corresponds to the symbols in the
battery compartment.
5. Installation
You can mount the wall clock on a wall using the opening on the back.
Warning – Mounting Note:
• Before mounting the clock, ensure that the chosen wall is suitable for
the weight to be mounted, and make sure that there are no electrical
wires, water, gas or other lines at the installation site on the wall.
• Purchase special fastening materials from specialised dealers.
• Do not mount the product above locations where people might be.
2
6. Operation
• Once the battery is inserted properly, the clock will automatically be set to
12:00 pm and its reception will be activated. As soon as the DCF signal
was received and processed (approx. 3 minutes up to a maximum of 15
minutes), the correct time is displayed automatically.
• Do not move the clock during this process.
• If the clock has not correctly set itself after 15 minutes, there is a problem
with the reception or with the selected location.
• Repeat the setting process at another location. To do this, remove the
battery for approximately 1 minute and then reinsert it into the battery
compartment. After you have changed the location of the device, use a
pointed object (e.g. a pen) to press and hold the WAVE button for about 2
seconds. The clock automatically sets itself to the 12 o'clock position and is
once again ready to receive the DCF signal.
Note
Note that electronic devices such as TVs, PCs, etc. can interfere with
reception when located within up to two metres of the product.

6.1. Manual setting

If a DCF signal can de nitely not be received at the installation location, set
the time manually.
• To set the time manually, use a pointed object (e.g. a pen) to press and
hold the SET button. The clock will continue to advance as long as the SET
button is held.
• If you press the RESET button, the clock automatically moves to the 12
o'clock position, even if you do not hold the button.
7. Care and Maintenance
Only clean this product with a slightly damp, lint-free cloth and do not use
aggressive cleaning agents. Make sure that water does not get into the
product.
8. Warranty Disclaimer
Hama GmbH & Co KG assumes no liability and provides no warranty for
damage resulting from improper installation/mounting, improper use of the
product or from failure to observe the operating instructions and/or safety
notes.
9. Technical Data
Radio Controlled DCF Wall Clock
Power supply
10. Declaration of Conformity
Hereby, Hama GmbH & Co KG declares that the radio equipment
type [ 00123159, 00186344] is in compliance with Directive
2014/53/EU. The full text of the EU declaration of conformity is
available at the following internet address: www.hama.com -> 00123159,
00186344 -> Downloads.
Frequency band(s)
1.5 V, 1 x AA battery (alkaline)
77.5 kHz
a