ROBBE ROXXY BL-CONTROL 900 OPTO Série Notice D'utilisation page 9

3. Programming the stick positions
NOTE!
The model type must be chosen (Parameter 4 or Parameter 5).
Otherwise the new parameters will not be stored.
3.1 Programming the stick positions "forward", "stop"
and "reverse"
1. Connect the controller according to the above photo
graph (with the exception of the power battery)
2. Turn on the Tx and move the throttle stick fully for
ward.
3. Connect Power Battery to the controller.
4. The controller will confirm connection with a short
beep.
5. After approximately 10 seconds you will hear a double
beep as confirmation of the fully forward position.
6. Move throttle stick to closed position, a short beep will
confirm.
7. Finally move the throttle stick to the reverse position; a
triple beep confirms the programming of the reverse
position.
Note:
If after (step 3.1.2) the red LED illuminates, then the SERVO-
REVERSE function must be operated in the Tx, remove power sup-
ply, reconnect and restart the programming (step 3.1.1).
The fully forward position of the stick must be set near the mechani-
cal stick limit.
3.2 Programming the stick positions "forward" and
"stop"
Programming the forwards and stop stick positions of the controller
should only be used in forwards operation (no reverse!); this is made
in a same manner up to step 3.1.6. The programmed stick positions
are confirmed with a triple beep.
4. Programming the speed controller parameters
4.1 Programming the speed controller parameters wit-
hout using the Programmer
Five parameters may be programmed in this manner.
Entry into programming mode is made by:
1. Controller connected as per the above photograph (except the
Power Battery)
2. Turn Tx on and move throttle stick to forward position.
3. Connect Rx battery supply
4. Controller will beep to confirm.
5. After approximately 10 seconds, you will hear a double beep
and after a further 3 seconds, a triple beep will be heard.
Parameter 1 has been chosen when the controller continuously
emits single beeps and the LED flashes.
The following stick movements set the program Parameters: Move
the throttle stick to closed position and quickly return to full
throttle. The controller will indicate the effective programming of
Parameter 2 by a continuing double beep and flash of the LED.
For programming Parameters 3, 4 and 5 the sequence described
above must be followed.
Parameter type
Parameter 1 Battery type
Parameter 2 Direction of motor rotation
- Brake ON / OFF (AIR)
Parameter 3 - Brake ON / OFF (HELI)
- Reverse ON / OFF (CAR, BOAT)
Parameter 4 Model type AIR / HELI
Parameter 5 Model type BOAT / CAR
Operating Instructions
Roxxy BL-Control 900 series Opto
Beep LED
1 x 1 x
2 x 2 x
3 x 3 x
4 x 4 x
5 x 5 x
9
To change the Parameters, the throttle stick must be moved quickly
from full throttle to the stop position and held for a minimum of 3 se-
conds in the stop position.
To set the parameters, move the throttle stick from the stop position
to full throttle and back.
Parameter type
Beep every 2 Sec.
Battery type
Direction of rotation
Brake (AIR)
Governor (HELI)
Reverse (CAR, BOAT)
Model type
(AIR / HELI)
Model type
(BOAT / CAR)
Moving the throttle stick quickly from stop to forward position stories
the changes.
Completing and storing the programmed settings is made by momen-
tarily removing the power supply battery.
The controller is now programmed and ready for operation.
4.2 Characteristics, protective functions
POR: start protection, stops involuntary starting of the motor
PCO: Low voltage cut-off, the motor will be stopped before the volt-
ages reaches a level where control is lost and potential deep dis-
charge damage to the cells can occur.
SPS: Super Programming System
Cool Power FET: Latest generation power transistor
Opto: Galvanic separation of the motor interference and receiver.
Rx-Filter: switches the controller OFF when a transmitter signal is not
present or corrupted.
TP: Thermal Protection
Hec: High motor frequency
LED ON LED flashes
Beep every 0,5 Sec.
LiPo NiCD/NiMH
Normal Reverse
OFF ON
OFF ON
OFF ON
AIR HELI
BOAT CAR