Care And Maintenance - Danby DCR412BLLH Guide D'utilisation Et Soins De Propriètaire

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

Defrosting
This refrigerator is equipped with a "Push Button"
(semi-automatic) defrost thermostat system. To
activate the defrost cycle, simply push in the red
defrost button located in the center of the control
knob (do not turn the control knob to zero/off). The
defrost cycle is initiated immediately. When
defrosting is complete, the "Push Button" will release
(pop-out) automatically and resume normal operating
conditions at the same temperature setting.
Push Button Defrost
NOTE: If the "Push Button" is activated (pushed-in)
accidentally, it will not be possible to "manually"
pull-out the push button (deactivate the defrost cycle).
You must let the defrost cycle run its course.
Defrosting of your refrigerator should take place
whenever ice build-up inside the freezer compartment
reaches 1/4" (6mm) thick. Defrosting may take a few
hours, depending on the amount of accumulated ice
and ambient indoor temperature. To speed up the
defrosting process, remove all frozen foods from the
freezer section. Leaving the door partially ajar for a
short period of time will also speed up the process.
Important: You must remember to close the
refrigerator door before the defrost cycle terminates
and normal operating conditions resume
automatically. The drip tray should be in position
directly below the freezer compartment to catch
condensed water during defrosting.
Note: Never use sharp or pointed instruments to
remove ice from the freezer compartment. The freezer
compartment contains refrigerated gas lines and if
accidentally punched/pierced, will render the
refrigerator inoperable and void the manufacturers
warranty.
DO NOT ALLOW THE REFRIGERATOR TO
CONTINUE OPERATION IF THE FREEZER
COMPARTMENT IS PIERCED.
After defrosting is complete, set the control to
maximum for 2 to 3 hours before returning to the
desired position. When the refrigerator is not to be
used for a long period of time, disconnect the
appliance from the electrical supply and leave the
door partially open. This will help to reduce mold and
mildew build-up.
Note: Wait 3 to 5 minutes before attempting to restart

CARE AND MAINTENANCE

the refrigerator if operation has been interrupted.
Cleaning
To clean the inside, use a soft cloth and a mixture of
one tablespoon of baking soda to one quart of water.
Other cleaning options are a mild soap suds solution,
or mild detergent. Wash glass shelves in a mild
detergent solution, then dry and wipe with a soft
cloth. Clean the outside with a soft damp cloth and
some mild detergent or appliance cleaner.
Vacation Time
For short vacation periods, leave the control knob at
its normal setting. During longer absences,
(a) remove all foods.
(b) disconnect power cord from electrical outlet.
(c) clean the refrigerator thoroughly, including drip
tray (defrost pan), located on the bottom of the
unit.
(d) leave door open to avoid possible formations of
condensate, mold or odors.
Power Failure
Most power failures are corrected within an hour or
two and will not affect your refrigerator temperatures.
However, you should minimize the number of door
openings while the power is off. During power
failures of longer duration, take steps to protect your
food by placing dry ice on top of packages.
If You Move
Remove or securely fasten down all loose items
inside the unit. To avoid damaging the leveling legs,
turn them all the way into the base.
Some Important Rules for the Correct Use of the
Refrigerator
• Never place hot foods in the refrigerator.
• Never place spoiled foods in the unit.
• Don't overload the unit.
• Don't open the door unless necessary.
• Should the refrigerator be stored without use for
long periods, it is suggested, after a careful
cleaning, to leave the door ajar to allow the air to
circulate inside the unit in order to avoid the
possibility of condensation, mold or odors.
4

Publicité

Table des Matières
loading

Table des Matières