Control Panel; Overhead Rigging - BEGLEC JB SYSTEMS LED OCTO PANEL Mode D'emploi

ENGLISH
DESCRIPTION:
1. Mains output with IEC socket: you can use a special IEC power cable to connect this output with the
mains input of the next Led OctoPanel for easier linking.
2. Mains input with IEC socket: connect the supplied mains cable here
3. fuse holder
4. ¼" jack used to connect the optional CA-8 controller
5. DMX input: 3pin male XLR-connector used to connect universal DMX-cables.
6. DMX output: 3pin female XLR-connector used to connect the unit with the next one in the DMX chain.
7. DISPLAY shows the various menus and the selected functions
8. MENU Button: to select the different menu functions
9. DOWN Button: to go backward in the selected functions
10. UP Button: to go forward in the selected functions
11. ENTER Button: to confirm the selected functions
12. DMX PRESENT led: indicates that a DMX signal is detected at the input
13. MASTER led: indicates that the unit works in master mode.
14. SLAVE led: indicates that the unit works in slave mode.
15. SOUND led: flashes to the sound of the music detected by the internal microphone.

OVERHEAD RIGGING

 Important: The installation must be carried out by qualified service personal only. Improper
installation can result in serious injuries and/or damage to property. Overhead rigging requires
extensive experience! Working load limits should be respected, certified installation materials
should be used, the installed device should be inspected regularly for safety.
 Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging
and servicing.
 Locate the fixture in a well ventilated spot, far away from any flammable materials and/or liquids. The
fixture must be fixed at least 50cm from surrounding walls.
 The device should be installed out of reach of people and outside areas where persons may walk by or be
seated.
 Before rigging make sure that the installation area can hold a minimum point load of 10times the device's
weight.
 Always use a certified safety cable that can hold 12times the weight of the device when installing the unit.
This secondary safety attachment should be installed in a way that no part of the installation can drop
more than 20cm if the main attachment fails.
 The device should be well fixed; a free-swinging mounting is dangerous and may not be considered!
 Don't cover any ventilation openings as this may result in overheating.
 The operator has to make sure that the safety-relating and machine-technical installations are approved by
an expert before using them for the first time. The installations should be inspected every year by a skilled
person to be sure that safety is still optimal.
JB SYSTEMS
®
OPERATION MANUAL
3/49 LED OCTOPANEL
ENGLISH
HOW TO SET UP THE UNIT

CONTROL PANEL:

MAIN MENU:
 To select any of the pre-set functions, press the MENU button up to when the required one is shown on
the display.
 Select the function with the ENTER button. The display will blink.
 Use DOWN and UP button to change the mode.
 Once the required mode has been selected, press the ENTER button to select. After 8 seconds the display
will automatically return to the main functions without any change. To go back to the functions without any
change press the MENU button. The main functions are shown on the right.
DMX512 Address Setting
Used to set the starting address in a DMX setup.
 Press the MENU button until
is shown
on the display.
 Press the ENTER button, the display starts
blinking.
 Use DOWN and UP buttons to change the
DMX512 address.
 Once the correct address shows on the display,
press the ENTER button to save it.
(or automatically return to the main functions
without any change after 8 seconds)
To go back to the functions without any change
press the MENU button again.
Auto setting DMX512 Address
 Press the MENU button until
is blinking
on the display.
 Press the ENTER button and the DMX512
address will automatically be set.
To go back to the functions: press the MENU
button again.
DMX channel setup mode
Used to set how many DMX channels the unit may
occupy:
 6
Channel mode: all 8 panels
programmed together
 9
Channel mode: 2x 4 panels
programmed together
 15 Channel mode: 4x 2 panels are programmed together
 24 Channel mode: all 8 panels are programmed individually for maximum flexibility!
 27 Channel mode: all 8 panels are programmed individually, including 3 extra effect channels
This is how to select the right DMX-channel mode:
 Press the MENU button until
is shown on the display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP buttons to select the desired channel mode: 6, 9, 15, 24 or 27 channel mode.
JB SYSTEMS
®
OPERATION MANUAL
are
are
4/49 LED OCTOPANEL