Char-Broil PERFORMANCE Série Mode D'emploi page 3

Ignitor Lighting
 Do not lean over appliance while lighting.
1.
Turn gas burner control valves to
2. Turn ON gas at cylinder.
3. Open lid during lighting.
4. To ignite, turn ignition burner knob to
5. Push and hold ELECTRONIC IGNITION button.
6. If ignition does NOT occur in 5 seconds, turn the
burner controls , wait 5 minutes and repeat
lighting procedure.
7. To ignite remaining burners, repeat steps 4 and 5.
If ignitor does not work, follow match lighting
instructions.
WARNING
Turn controls and gas cylinder off when not in
use.
Match-Lighting
 Do not lean over appliance while lighting.
1.Open lid. Turn on gas at cylinder.
2.Place match into match holder, light match and
place next to burner ports. (Holder maybe on left or
right side.)
3.Push in and turn burner knob to
being lit. Be sure burner lights and stays lit.
4.Light adjacent burners in sequence by pushing knobs
in and turning to
Hot Plate Ignitor Lighting
 Do not lean over appliance while lighting.
1.Open hot plate lid. Turn on gas at cylinder.
2.Turn hot plate knob to
, push and hold ELECTRONIC
IGNITOR button.
3.If hot plate does NOT light, turn knob to
minutes, then repeat lighting procedure.
Hot plate Match Lighting
1.Open hot plate lid. Turn on gas at cylinder.
2.Place lit match near burner.
3.Turn hot plate knob to
Be sure burner lights and stays lit.
Leak Testing Valves, Hose and
Regulator
Leak test at least once a year and every
time the cylinder is changed or
disconnected.
1. Turn all appliance control knobs to
2. Be sure regulator is tightly connected to gas
cylinder.
3. Turn on Gas. If you hear a rushing sound, turn
gas off immediately. There is a major leak at
the connection. Correct before proceeding.
4. Brush soapy solution (mixture of half soap and
half water) onto hose connections and areas
circled below.
5. If growing bubbles appear, there is a leak. Turn
off gas at cylinder immediately and check
tightness of connections. If leak cannot be
stopped do not try to repair. Call for replacement
parts.
6. Always turn off gas at cylinder after performing
leak test.
.
SPIDER AND WEBS
INSIDE BURNER
If your barbeque is getting hard to light or the
flame is weak, check and clean the venturis and
burners.
Spiders or small insects are known to create
"flashback" problems by building nests and laying
eggs in the barbeque's venturi or burner
obstructing the flow of gas. The backed-up gas
can ignite behind the control panel. This
flashback can damage your barbeque and cause
injury. To prevent flashbacks and ensure good
performance, the burner and venturi tube
assembly should be removed and cleaned
whenever the barbeque has been idle for an
extended period of time.
Cleaning the Burner Assembly
for burner
Follow these instructions to clean and/or replace parts
of burner assembly or if you have trouble igniting
appliance.
Turn gas off at control knobs and cylinder.
1.
2. Remove cooking grates, flame tamers, carryover
tubes and burners.
3.
Detach electrode from burner.
4.
Carefully lift each burner up and away from valve
openings.
, wait 5
5.
We suggest three ways to clean the burner tubes. Use the one
easiest for you.
(A) Bend a stiff wire (a light weight coat hanger
works well) into a small hook. Run the hook
through each burner tube several times.
(B)
Use a narrow bottle brush with a flexible handle (do not
use a brass wire brush), run the brush through each
burner several times.
(C) Wear eye protection: Use an air hose to force air
into burner tube and out burner ports. Check each
port to make sure air comes out each hole.
6.
Wire brush entire outer surface of burner to
remove food residue and dirt.
7.
Clean any blocked ports with a stiff wire such
as an open paper clip.
.
8.
Check burner for damage, due to normal wear and
corrosion some holes may become enlarged. If any
large cracks or holes are found replace burner.
VERY IMPORTANT: Burner tubes must
reengage valve openings. See
illustration at right.
Correct
burner-to-valve
engagement
9.
Attach electrode to burn. e r
Carefully replace burners.
10.
11.
Attach burners to brackets on firebox.
12.
Reposition carryover tubes and attach to burners.
Replace flame tamers and cooking grates.
Firebox burner
bracket
CAUTION
SPIDER ALERT!
Electrode
Pry off
electrode with
a flat blade
screwdriver
Storing Your appliance
•Clean cooking grates.
•Store in dry location.
•When gas cylinder is connected to appliance, store
outdoors in a well-ventilated space and out of reach
of children.
•Cover appliance if stored outdoors.
•Store appliance indoors ONLY if gas cylinder is turned
off and disconnected, removed from appliance and
stored outdoors.
•When removing appliance from storage check for burner
obstructions.
General appliance Cleaning
Clean appliance often, preferably after each
•
cookout. If a bristle brush is used to clean any of the
appliance cooking surfaces, ensure no loose bristles
remain on cooking surfaces prior to grilling. It is not
recommended to clean cooking surface while
appliance is hot.
appliance should be cleaned at least once a year.
•Do not mistake brown or black accumulation of
grease and smoke for paint. Interiors of gas grills
are not painted at the factory (and should never be
painted). Apply a strong solution of detergent and
water or use a appliance cleaner with scrub brush on
insides of appliance lid and bottom. Rinse and allow
to completely air dry. Do not apply caustic
appliance/oven cleaner to painted surfaces.
• Plastic parts: Wash with warm soapy water and wipe
dry.
 Do not use citrisol, abrasive cleaners, degreasers or
a concentrated appliance cleaner on plastic parts.
Damage to and failure of parts can result.
•Porcelain surfaces: Because of glass-like
composition, most residue can be wiped away with
baking soda/water solution or specially formulated
cleaner. Use nonabrasive scouring powder for
stubborn stains.
•Painted surfaces: Wash with mild detergent or
nonabrasive cleaner and warm soapy water. Wipe
dry with a soft nonabrasive cloth.
•Stainless steel surfaces: To maintain your
appliance's high quality appearance, wash with mild
detergent and warm soapy water and wipe dry with
a soft cloth after each use. Baked-on grease
deposits may require the use of an abrasive plastic
cleaning pad. Use only in direction of brushed finish
to avoid damage. Do not use abrasive pad on
areas with graphics.
• Cooking surfaces: If a bristle brush is used to clean
any of the appliance cooking surfaces, ensure no
loose bristles remain on cooking surfaces prior to
grilling. It is not recommended to clean cooking
surfaces while appliance is hot.
IF APPLIANCE FAILS TO LIGHT
Make sure gas is turned on at cylinder.
Make sure there is gas in the cylinder.
Does the ignitor make a sparking Noise?
If yes check for spark at burner.
If no spark check for damaged or loose wires.
If wires are OK check for cracked or broken electrode,
replace if needed.
If wire or electrodes are covered by cooking residue,
clean electrode tip with alcohol wipe if needed.
If needed replace wires.
If no sound check battery.
Make sure battery is installed correctly.
Check for loose wire connection at module and switch.
If ignitor continues to not work then use match.
Høyre
skinne
3