Beta 601C Mode D'emploi page 9

INSTRUCTIONS FOR USE
‡ 3ODFH WKH DQJOH LQGLFDWRU RQ WKH WRRO DQG TXLFNO\ SUHVV EXWWRQ 66 WR VWDUW WLJKWHQLQJ 7KH DQJOH LQGLFDWRU LV ¿WWHG ZLWK D PDJQHW
to provide perfect stability (picture 2-o).
‡ :KHQ  RI WKH VHOHFWHG DQJOH LV UHDFKHG WKH ¿UVW JUHHQ /(' ZLOO WXUQ RQ DQG WKH EX]]HU ZLOO VRXQG
• When the set angle value is reached, the red LED will turn on.
• To store the value of the torque angle, press button M.
CAUTION: ,I WKH WLJKWHQLQJ SURFHVV LV LQWHUUXSWHG IRU D IHZ VHFRQGV WKH GLVSOD\ ZLOO EOLQN FRQ¿UPLQJ WKDW WKH UHTXLUHG DQJOH KDV
been reached. To resume tightening, press button (S/S). To zero the device, press button C.
• To start a new tightening operation, press button S/S.
If the display is not used for approximately 2 minutes, it will automatically turn off.
SETTING UP MENU
.HHS EXWWRQ 66 SUHVVHG WR HQWHU WKH FRQ¿JXUDWLRQ PHQX 3UHVV EXWWRQ 66 VHYHUDO WLPHV WR HQWHU WKH PHQXV &+$1*,1*
TORQUE DIRECTION, TORQUE MEMORIES AND RESETTING TORQUE MEMORIES.
CHANGING TORQUE DIRECTION MENU
- The display will show PoS for the clockwise direction of rotation, and nEG for the anticlockwise direction
of rotation respectively.
 3UHVV EXWWRQV
- To quit the menu, press button (S/S) several times.
TORQUE MEMORIES MENU
 7KLV PHQX SURYLGHV WKH YDOXHV RI WKH PHDVXUHG DQG VWRUHG WRUTXH DQJOHV XS WR  YDOXHV VWRUHG 
- If no values have been stored, the display will show nonE.
 :KHQHYHU EXWWRQV
- To delete one of the stored values, press button C twice.
- To quit the menu, press button (S/S) several times.
RESETTING TORQUE MEMORIES MENU
- This menu allows all the values stored in the TORQUE MEMORIES MENU to be deleted.
- The display will show ClrA
- To delete all the stored values, press button C.
- The display will show no?
- To delete all the stored values, press button C. To cancel the operation, press button S/S.
- To quit the menu, press button S/S twice.
ERROR MESSAGES
- Er4 indicates that the value has not been set correctly. Press button C to repeat the operation. Do not move the
angle indicator while setting.
 (U LQGLFDWHV WKDW WKH DQJOH LQGLFDWRU LV QRW ZRUNLQJ FRUUHFWO\ 3UHVV WKH 5(6(7 EXWWRQ
- Er--- indicates that the angle indicator was rotated too quickly during a measurement. Press button C to repeat the
operation.
 )XOO LQGLFDWHV WKDW QR GDWD FDQ EH VWRUHG LQ WKH PHPRU\ WKH PHPRU\ LV IXOO 'HOHWH VRPH RI WKH  VWRUHG GDWD
RESET
- If the angle indicator is not working correctly, press the RESET button to zero the device (picture 2-r). The angle
indicator can also be zeroed by removing the batteries.
DQG WR FKDQJH WKH GLUHFWLRQ RI URWDWLRQ
DQG DUH SUHVVHG WKH GLVSOD\ ZLOO VKRZ WKH VWRUHG YDOXHV RI WKH WRUTXH DQJOH
EN
9