Publicité
Les langues disponibles
Les langues disponibles
PXFE868
Montage- und Anschlussanleitung / Funkempfänger
Mounting and wiring instructions / Wireless receiver
Instructions de montage et de câblage / Récepteur sans fil
English
Operation mode
LED 1
LED MD
Relay energised
on
flashes
Relay energised,
on
on
inverse output
Switch functions
Linkage
flashes
on
slowly
Latching function on
flashes
Wiping
flashes
flashes
function
slowly
slowly
Additional func-
Battery moni-
off (LED
flashes
toring
3 flash-
slowly
es)
Status monitor-
off (LED
flashes
ing
4 flash-
slowly
es)
Notice
If only one or both additional functions are activated, no further wireless
transmitter can be taught in.
Operation mode wiping contact
- Choose or select wiping function. LED MD flashes.
- With each flashing of the LED, the wiping time is increased by 1 s.
- Count the impulses of the flashing LED and confirm the desired time by
pressing the LRN push-button.
- In order to change the wiping contact time, start selection of operation
mode and select wiping function again.
Operation mode status monitoring
- After selection of status monitoring the LED MD flashes
every second.
- The LEDs 1-4 indicate the adjustable status times.
- The display of the LED changes every 5 s (see table).
- If the required LED combination is indicated, press the LRN push- but-
ton for 1 s. The desired operation mode is now activated.
- Without confirmation of the selection, the standard value of 10 s
is set.
Function
Relay energised by provid-
Relay energised by pro-
viding operating voltage,
inverse output signal
Relay energised as soon as
one switch is actuated, de-
energises when all taught-in
switches are not actuated
Latching function/impulse
Wiping function, contact au-
tomatically de-energises after
the set time
Relay K3 indicates under-
voltage of the taught-in and
battery-powered switches/
transmitters
Relay K4 indicates status
error; activates function only
in combination »switch with
status signal«
4 / 12
Status
LED 1
LED 2
signal time
10 s
on
off
100 s
on
on
1000 s
on
on
10000 s
on
on
Function: If no status information is given by the taught-in switches, relay
K4 automatically gives the alarm after 2.2 times the status time.
Attention! Please ensure that the taught-in wireless transmitter is set to
the correct status signal.
Teaching in of switch
- Press push-button LRN approx. 1 s -> LED MD flashes slowly (2 Hz).
- Press push-button SEL for channel seletion.
- Actuate switch/command device to be taught in -> the LED of the cor-
responding channel is off for short time.
- To leave teach-in mode press push-button LRN for approx. 1 s -> LED
MD is on.
Deleting one switch
- Press push-button LRN for 5 s until LED MD flashes fast (5 Hz).
- Press push-button SEL for channel seletion.
- Actuate switch/command device to be deleted -> the LED of the corre-
sponding channel flashes for a short time.
- Press push-button LRN for approx. 1 s to leave delete mode.
Inverse teaching in of one switch
- Procedure like teach-in but switch must be actuated before proce-
dure is started by pressing LRN.
Deleting all switches
- Press push-button LRN for 5 s until LED MD flashes fast (5 Hz).
- LED 1 is on -> release push-button LRN.
- Press push-button LRN for 5 s again.
- LED MD is on and LED 1 flashes fast -> release push-button LRN.
- Operation mode was set back to standard.
LED 3
LED 4
LED MD
off
off
flashes every s
off
off
flashes every s
on
off
flashes every s
on
on
flashes every s
®
Publicité
