Venmar VÄNEE COMMANDE DELUXE 20-40-60 Guide D'installation Et D'utilisation

I
NSTALLATION AND
The illustrations in this document are generic; your control appearance may be slightly different from the ones shown.
Wear safety glasses and gloves while performing these instructions (steps 1 to 5).
This auxiliary control must be paired with the Advanced Touchscreen Control.
INSTALLATION

Unplug the ventilation unit.
NOTE: If the control is to be installed in an electric box,, go to step

7
Cut a 2 / " x 1¾" hole in a wall, at a
8
convenient location for the control. See
figure at right.

Temporarily place the control over the
hole and mark both mounting screw hole
positions.

Remove the control, drill both screw
holes (3/16" Ø) in wall and insert the wall
anchors (included).

Mount the control to the wall.

Plug the ventilation unit.

Disengage the control from its support
by lifting and tilting the bottom part of the
control.
NOTE: This wall control requires 2 AAA 1.5 V
batteries (included).

Install the batteries at the back of the
control.

Keep the auxiliary control in hand. Go
to the main control. Reach the Wireless
Connection screen (see figure at right)
following this path:
HOME PAGE
the gear at the bottom right)\
\
INSTALLATION WIRELESS CONNECTION
on the auxiliary control button for 5
seconds. The LED indicator will fade
in and out to indicate the system is
trying to pair the auxiliary control with
the main control. The main control will
detect the item. This procedure will take
30 s max. Press on + to complete pairing. Once the pairing is
done, the item will move in the upper part of the screen and a √
will appear at the left of the item.
NOTE: It is possible to unpair an item by pressing on x.
U G
SER
EE . 41301 V
VÄN PART NO
READ AND SAVE THESE INSTRUCTIONS
Ø 3/16", typ.
VC0206A
VC0195
VO0291
WIRELESS CONNECTION
(press on
\
SETTINGS
. Press
VC0207A
20-40-60 D
UIDE FOR
ENMAR PART NO
!
WARNING

If needed,
Auxiliary Control screen (see figure
at right) following this path:
(press on the gear at the bottom right)\
.
\
PREFERENCES AUTOMATIC AUXILIARY CONTROL
to modify the humidity detection feature.

L
Install the auxiliary control back in its
support. Insert the top brackets in the
notches. Push on the bottom part of the
control until it clicks in place.

M
Test the wall control.
HOW TO USE THE CONTROL
VC0209
HOW TO CHANGE THE BATTERIES
If a batteries change is required, the low batteries indicator will flash
for 5 seconds when pressing on the button.

Perform step to access the batteries.
Remove the old batteries. Dispose of used batteries as per local
rules and regulations.
Replace the batteries. The use of rechargeable batteries is not
recommended.
Perform step L to install the auxiliary control back in its support.
P
ROBLEM
No detected item on Wireless
Connection screen
LED indicator does not light up
when pressing on the button
Humidity sensor does not work Low batteries
C
ELUXE ONTROL
. 41401
reach the Automatic
HOME PAGE
VC0208A
The button works following this sequence:
• Click 1 = 20 min
• Click 2 = 40 min
• Click 3 = 60 min
• Click 4 = OFF
• and so on
The indicator lights up as per the selected
duration and the system exchanges air at
MAX speed.
If the humidity sensor detects a humidity
rise, the exhaust fan will activate in MAX
speed for a 20-minute, a 40-minute or a
60-minute period as per the Automatic
Auxiliary Control setting.
TROUBLESHOOTING
C
AUSE
The batteries are not installed
Low batteries
The batteries are not installed
Low batteries
Range too high between the
auxiliary control and the main
control
Sensitivity too low, set
sensitivity to High in the
Automatic Auxiliary Control
screen
AUXILIARY CONTROL
SENSITIVITY SENSITIVITY
VO0292
23851 rev. 01