Table des Matières
Publicité
Système Programmable CA
Note 5: VuMètre
+0
MSW1 (Commutateur Microphone 1): C0h = ACC, 90h = UP, 60h = DOWN, 30h = PTT
+1
FWD (Tx Puissance directe): 00h ~ FFh
+2
REV (Tx puissance réfléchie): 00h ~ FFh
+3
S Niveau (S-mètre): 00h ~ FFh
+4
MIC (Niveau Microphone): 00h ~ FFh
+5
NOISE (Niveau) Squelch: 00h ~ FFh
+6
MSW2 (Commutateur Microphone 2): 90h = P2, 60h = P1, 30h = P
+ 7
TEMP (Température Transistor Final): 00h ~ FFh
+8
ALC (Niveau ALC): 00h ~ FFh
Note 6: Read Status Flags
+0 Status 0
Status 0
Bit 0
SPLIT: 1 = on, 0 = off
+1 Status 1
1
Not Used
+2 Status 2
2
TUNE: 1 = active, 0 = attente
3
CAT IN: 1 = on, 0 = off
+3 Status 3
4
Not Used
+4 Status 4
5
PUISSANCE: 1 = on, 0 = off
+5 Status 5
6
MUTE: 1 = on, 0 = off
7
TX IN: 1 = on (Tx), 0 = off (Rx)
+6 Status 6
+7 Status 7
Status 2:
Bit 0
FAST: 1 = on, 0 = off
1
COUPLEUR: 1 = on, 0 = off
2
BKMR: 1 = Canal mémoire Vacant evité quand rappel d'un Canal mémoire
0 = tous les Canaux mémoires choisis quand rappel d'un Canal mémoire
3
LOCK: 1 = Cde pal. fréq. Verr., 0 = Cde pal. fréq. Deverr.
4
SQLSC: 1 = on, 0 = off
5
UPSCN: 1 = Up Scan, 0 = Down Scan
6
MEM: 1 = Mode mémoire, 0 = autre mode (commeMode VFO)
7
SRCH: 1 = Recherche dynam.on, 0 = Recherche dynam. off
Status 3:
Bit 0
1 MHz: 1 = 1 MHz Up/Down on, 0 = 1 MHz Up/Down off
1
10 MHz: 1 = 10 MHz Up/Down on, 0 = 10 MHz Up/Down off
2
FMLOC: 1 = FM auto lock on, 0 = FM auto lock off
3
Not Used
4
CATTX: 1 = Tx on CAT cde, 0 = Rx on CAT cde
5
NOTX: 1 = Tx Inhibit on, 0 = Tx Inhibit off
6
KEYUP: 1 = Active la fonction quand touche relachée,
0 = Activer la fonction quand touche appuyée
7
PTTWA: 1 = PTT waiting on, 0 = PTT waiting off
Status 4:
Bit 0
Not Used
1
DSPBP: 1 = DSP BPF on, 0 = DSP BPF off
2
DSPNT: 1 = DSP NOTCH on, 0 = DSP NOTCH off
3
DSPNR: 1 = DSP N.R on, 0 = DSP N.R off
4
ALOCK: 1 = Panel Lock on, 0 = Panel Lock off
5
GROUPE: 1 = Canal groupe mémoire on,
0 = Canal groupe mémoire off
6
PRGM: 1 = PMS on, 0 = PMS off
7
Not Used
Status 6:
Bit 0
DULON: 1 = Double veille on, 0 = Double veille off
1
DULCK: 1 = Vérif. Double veille , 0 = autre état
2
Not Used
3
BUSY: 1 = BUSY on, 0 = BUSY off
4
Not Used
5
AGCSL: 1 = AGC Slow, 0 = autre état (comme AGC Auto)
6
AGCFS: 1 = AGC Fast, 0 = autre état (comme AGC Slow)
7
MTMOD: 1 = TOS Mètre, 0 = Indicateur ALC
FT-100D F
IELD
CA T T T T T E/R assisté par Ordinateur
CA
CA
CA
C
Notice d'emploi
OMMANDER
Status 1:
Bit 0
Not Used
1
MR CHK: 1 = on, 0 = off
2
B VFO: 1 = VFO B on, 0 = VFO B off
3
QMB: 1 = on, 0 = off
4
M TUNE: 1 = on, 0 = off
5
VFO: 1 = Mode VFO, 0 = autre Mode (comme Mode QMB)
6
MEM: 1 = Mode mémoire, 0 = autre Mode (commeMode VFO)
7
SRCH: 1 = Recherche dynam. on, 0 = Recherche dynam. off
Status 5:
Bit 0
ARTS: 1 = ATRS on, 0 = ARTS off
1
BKIN: 1 = CW Break-in on, 0 = CW Break-in off
2
KEYER: 1 = CW Keyer on, 0 = CW Keyer off
3
AUTTX: 1 = DSP N.R on, 0 = DSP N.R off
4
Not Used
5
Not Used
6
WAIT: 1 = Coupl. Ant. attente, 0 = Coupl. Ant. Actif
7
HI SWR: 1 = HI SWR on, 0 = HIGH SWR off
Status 7:
Bit 0
SIDE: 1 = Ec. Loc. CW on, 0 = Ec. Loc. CW off
1
MUFST: 1 = Menu rapide on, 0 = Menu rapide off
2
Not Used
3
Not Used
4
Not Used
5
PROC: 1 = Compr. BF on, 0 = Compr. BF off
6
NBON: 1 = Noise Blanker on, 0 = Noise Blanker off
7
VOXON: 1 = VOX on, 0 = VOX off
101
Publicité
Table des Matières
