Table des Matières
Publicité
ENGLISH
KRYO 65/ST KRYO 65/AT
Coffee doser grinder
KRYO 65 OD
Coffee grinder on demand
1. INSTALLATION
Installation must be performed by a qualified technician.
The machine is delivered ready for installation according to the
data on the plate Fig. 3.
Check that the main power supply is compatible with the machine.
Check that the machine, the accessories, the supply cable and the
plug are intact, and in the event of damage, inform the retailer
promptly.
The machines have been designed and built for grinding coffee
beans for professional use.
Any other use is to be considered improper and thus dangerous.
2. FIRST START-UP
KRYO 65 is equipped with a locking device to secure the bean
hopper (Fig. 4). Lock the device when the grinder is in use.
The locking device is marked on the outside of the bean hopper. If
the slot of the device points to the marking, the bean hopper can
be mounted or removed. To secure the bean hopper turn the slot
to the left.
2.1. Description of commands
KRYO 65/ST
Main switch (Fig. 1-9) with two positions; when switched on, the
machine is on and starts coffee grinding.
KRYO 65/AT
Main switch (Fig. 1-9) has two positions; in position (I), the
machine is on and automatically shuts off when the doser is full
enough.
KRYO 65 OD
Main switch (Fig. 1-9) with two positions; when switched on, the
machine is ready for coffee grinding.
KRYO 65 OD has a startup menu to select the personal
preferences of the operator, when switched on for the first time.
Operator has to choose the language, the mode and the way to
activate the grinding. After choosing the preferences, the display
will show a message "Do Calibration". The calibration has to be
done with the procedure shown in the software structure under
Counter/Burrs/Calibration.
This message will be shown after each preparation up to the
time, the calibration has been done.
2.2. Grind setting
The manufacturer tests the coffee grinder with a medium grind
setting. The setting depends on the type of coffee used.
- Place a small quantity of coffee beans in the bean hopper
and close the lid;
- Check that the hopper locking slide is open (Fig. 1–4)
- KRYO 65/ST KRYO 65/AT: Grind a small quantity of coffee.
Position the filter holder on the filter holder fork (Fig. 1-8),
then pull the dosing lever (Fig. 1a-11) to dispense a dose of
ground coffee;
- KRYO 65 OD: Position the filter holder on the filter holder
fork (Fig. 1-8) and grind coffee;
- Brew some coffee, checking the dispensing time, the
appearance of the coffee and its taste, considering that
excessively course grounds produce light coloured coffee
without a crema, while grounds that are too fine result in
strong, dark coffee without a crema.
- If the coffee does not respond to your desired requirements,
adjust grind fineness by pressing the ring block button (Fig. 2-1)
and turning the regulation knob (Fig. 2-3) counter-clockwise for
a finer grind or clockwise for a coarser grind.
- Repeat the operation until you have obtained the desired
quality of coffee.
Recalibration of the grind is typically only necessary after a change
in coffee. Minor adjustments may be required throughout use to
accommodate for changes in freshness of the beans.
2.3. Adjusting the ground coffee dose
Adjust the doses of KRYO 65/ST and KRYO 65/AT as followed:
- Turn the knob below the doser (Fig. 1a-12) counter-clockwise
to increase the dose or clockwise to decrease the dose.
- Pull 6 times the lever (Fig. 1a-11) and check the dose each
time. Take care that the dosing star is completely covered
with ground coffee
3. MAINTENANCE
Maintenance operations should be carried out with the machine
turned off and with the plug removed from the power source.
We recommend the cleaning products you can buy from us.
Do not use metallic or abrasive tools, such as steel wool, metal
brushes, needles, etc., or detergents (alcohol etc.), but simply a
damp cloth or sponge.
3.1. Daily
- Clean the housing and the grounds tray.
- Clean fork area for the filter holder.
- Clean the coffee outlet with a brush.
3.2. Periodically or after intense use
Empty the bean hopper, and clean it of oily residues left by the
coffee with a mild soap solution. Rinse thoroughly!
Waste materials used for processing or maintenance, if not
biodegradable or pollutant, should be placed in separate
containers and taken to suitable collection centers.
13
Publicité
Table des Matières
