Arke Fontanot Civik Spiral Staircase Kit Instructions De Montage page 7

24. Tighten the part B03 completely (fig. 10).
25. Tighten the part B02 of the upper treadcompletely (fig. 2).
26. C heck once more the vertical position of the railing balusters (C03) and, if necessary, correct it, by repeating the
previous operations.
27. S et the first baluster (C03 - H 1190 mm - 46
(C03 - H 1190 mm - 46
28. F ix into the floor in relation to the first baluster (C03), the part F01, by drilling with 8 mm (
the parts C58, B12 and B02 (fig. 1).
29. F ind the handrail piece marked with letter "M" (A22) and the one with letter "R" (A23) which will be used for the
railing of the landing (E03) (fig. 11).
30. S tart to model the handrail pieces (A22) marked with "M", in order to give it the handrial staircase's shape most
alike (fig. 1).
31. B eginning from the baluster (C03) on the landing (E03), start to fix the handrail (A22),that you have already
slightly bent in the previous operation. Use the parts C64.
32. C onnect all other handrail pieces (A22), by screwing, glueing and shaping them. Use the parts B33, D72 and the
glue (X01).
33. W hen you reach the first baluster (C03) at the bottom of the stair, cut the excess piece of the handrail with a
hacksaw.
34. Complete the handrail (A22) by assembling the part A37. Use the parts C64 and the glue (X01) (fig. 1).
35. F it all remaining railing balusters into the treads (L02), tighten the part B02 and fix to the handrail (A22), paying
attention to the vertical position (for the stairs with a diameter larger than 140 cm (55
first assemble the shorter balusters) (fig. 12).
36. Check again the regular shape of the handrail (A22) and, if necessary, correct it with a rubber hammer.
37. Complete the railing assembly by fitting the parts B82 into the lower part of the balusters (C03) (fig. 1).
Assembly of the Balustrade
38. Screw the baluster (C04) into the part G01 that sticks out from the landing (E03) (fig. 10).
39. Assemble the parts F01 into the holes of the landing (E03), using the parts B07, B06, B23 (fig. 1).
40. Position the shorter balusters (H. 935 mm - 36
41. Fix the part A36 into the baluster (C04), by using the part B02 (fig. 1).
42. Fix the handrail (A23) marked with the letter "R", using the parts C64 (fig. 1).
43. I n case there were walls around the stair and depending on their position, it could be necessary to set one or
two more balusters (H. 935 mm - 36
44. I n that case it is necessary to consider either the distance between all other balusters, or otherwise the
distance from the wall. For the fixing it is suggested to drill the landing (E03) with 9 mm (
to use the fixing parts F01, B02, B07, B06, B23. Whereas for the fixing into the floor it is suggested to drill with
15/32
" ) drill bit and to use the parts F01, B02, B87 (fig. 13).
the 12 mm (
Final Assembly
45. I n order to tighten the staircase at the intermediate points, you must fix into the wall the parts F09 and connect
them to the balusters (C03) by using the part F08. Drill the wall with a drill bit 8 and use the parts C50, C49,
C58, B12 (fig. 14).
46. Stick the panels (H01) to the treads (L02) using the part B96 (fig. 1).
47. Stick the panels (H03, H04), to the landing (E03) using the part B96 (fig. 1).
7/8
7/8
" ) to obtain the same size as all others you assembled previously.
13/16
" ) (fig. 12).
" ) together with the reinforcing part (F07). Cut one long baluster
13/16 " ) and tighten the part B02 (fig. 1).
7 - ck
5/16
" ) diameter bit. Use
1/8
" ), we suggest that you
23/64 " ) diameter bit and