Geneva Cinema Mode D'emploi page 10

trouBlEshooting
Online support: support.genevalab.com
gEnEral
how do i clean the speaker cabinet?
The cabinet can be cleaned with a water dampened cloth. Use a
non-scratching cloth only. Do not use paper towels ( household paper ),
because it can contain glass fiber which can leave scratches.
Light soap water can be used, but never hot water. When cleaning,
make sure you do not touch the GENEVA logo and the touch keys.
Do not use any household cleaner, polish, wax or any other chemicals
as it will damage the cabinet paint.
how do i change the battery of the remote control?
1. Push the pin included in the packaging into the small hole at the
end of the remote control.
Alternatively, you can use the end of a bent paper clip.
2. Push the pin inside, until the battery compartment moves outside.
3. Replace the battery ( 3V lithium cell, CR2032 ). Ensure that the
correct polarity is observed. The "+" sign on the battery must be on
the same side as the "+" of the battery holder.
What is the power consumption in standby?
0.35 Watt ( powered off via the remote control or power key on top
of the unit ).
What is the maximum weight i can put on the Model cinema?
25 kg. or 55 lbs.
tv
there is no audio from the tv
• Check the TV setup menu, in "Speaker Selection" select "External
Speakers", do not use "TV speakers".
• Check the TV setup menu, in "SPDIF/optical output" select "PCM".
Do not select "automatic" or "Dolby Digital".
the volume of the tv is too low — i cannot hear much
Make sure both volume of the TV and the Model Cinema is correctly
adjusted.
the volume of the tv is too high — i hear distortions
There is an advance procedure to adjust the input gain. Go to
support.genevalab.com.
Why do totalvolume and voice Enhancement have no effect on
the audio?
TotalVolume and Voice enhancement work only in TV mode, they are
not supported in the Line-In or Bluetooth modes.
8
Why does the Model cinema turn itself off?
The Model Cinema has an automatic power on and off function. If there
is no audio input for a few minutes, it will turn itself automatically off.
This function can be disabled by holding
can i disable the automatic power-on Function?
Yes. Hold for a few seconds.
can i disable the automatic source selection of the tv
audio inputs?
Yes. Press and hold for a few seconds, then select one of the three
TV audio inputs via TV. If the automatic TV input selection is disabled,
then the automatic power-on function is also disabled.
Why is the Model cinema not automatically powered on when the
tv is on?
Then the automatic power-on function is disabled, or the automatic
audio source selection is disabled. Both functions must be enabled to
power on the TV automatically.
i can hear the tv, but when i play the dvd i cannot hear anything
Perhaps, your TV sends compressed audio ( Dolby Digital / AC3 or DTS )
via the digital audio inputs ( coaxial or optical ). The Model Cinema does
not support these formats. Make sure the settings in the TV are correct,
for "audio output" select "uncompressed audio / PCM". "Automatic" or
"Multichannel 5.1 output" are incorrect selections.
the tv is off, but Model cinema is turning itself on again
Most likely there is still an active audio signal connected, which is
turning the Model Cinema on. Make sure you connect one cable only
from the TV to the Model Cinema.
BluEtooth
how to reset the Bluetooth
Up to 8 paired Bluetooth devices can be stored. To erase the memory,
proceed as follows:
1. Select Bluetooth using the remote control.
2. Within 5 seconds after entering Bluetooth mode, press and hold
down until the dis play shows "RESET".
3. Pair your mobile phone again.
support
service and repair
If the product is damaged and needs repairs, please contact your
dealer. Visit www.genevalab.com to find a dealer in your area.
Warranty
See the specific terms for your country at www.genevalab.com.
for three seconds.