Publicité
Liens rapides
ULTRA-MAX™ GAS GRIDDLE MODELS
GRILS A GAZ ULTRA-MAX MODELES
824M
836M
848M
860M
872M
WARNING:
Improper installation,
adjustment, alteration, service or
maintenance can cause property
damage, injury or death.
installation, operating and maintenance
instructions thoroughly before installing
or servicing this equipment.
AVERTISSEMENT: L'installation inexacte, le réglage,
le changement, le service ou l'entretien peuvent
causer des dégats matériels, des dommages ou la
mort. Lisez les instructions d'installation, d'opération
et d'entretien complètement avant d'installer ou
entretenir ce matériel.
FOR YOUR SAFETY:
use gasoline or other flammable vapors or
liquids in the vicinity of this or any other
appliance.
POUR VOTRE SÛRETÉ: N'enregistrez pas ou
n'utilisez pas l'essence ou d'autres vapeurs ou
liquides inflammables à proximité de ceci ou d'aucun
autre appareil.
Star
Manufacturing
International Inc.
10 Sunnen Drive
St. Louis, MO 63143
Phone: (314) 781-2777
Fax: (314) 781-2714
824T
836T
848T
860T
872T
Read the
Do not store or
824TS
836TS
848TS
860TS
872TS
WARNING:
This appliance shall be
installed in accordance with current
regulations and used only in well-
ventilated space. Refer to instructions
before installing and using this
appliance.
AVERTISSEMENT: Cet appareil sera installé
selon des règlements actuels et utilisé
seulement dans l'espace bien-aéré. Référez-
vous aux instructions avant d'installer et utiliser
cet appareil.
In addition, there should be posted, in a
prominent location, detailed instructions
to be followed in the event the operator
smells gas. Obtain the instructions from
the local gas supplier.
En outre, là devrait être signalé, dans un
emplacement en avant, des instructions détaillées
d'être suivi en cas que l'opérateur sent le gaz.
Obtenez les instructions du fournisseur local de
gaz.
Installation and
Operating Instructions
Instructions d'installation
et d'opération
2M-Z4877 Rev. G 2/10/2010
824TSCHS
836TSCHS
848TSCHS
860TSCHS
872TSCHS
Publicité
Sommaire des Matières pour Star Manufacturing International ULTRA-MAX 824M
- Page 1 Star Installation and Manufacturing Operating Instructions International Inc. Instructions d’installation 10 Sunnen Drive St. Louis, MO 63143 et d’opération Phone: (314) 781-2777 Fax: (314) 781-2714 2M-Z4877 Rev. G 2/10/2010 ULTRA-MAX™ GAS GRIDDLE MODELS GRILS A GAZ ULTRA-MAX MODELES 824M 824T 824TS 824TSCHS 836M...
-
Page 2: Safety Symbol
8:00 am to 4:30 p.m. Central Standard Time Business Hours: (800) 807-9054 Local (314) 781-2777 Telephone: (800) 396-2677 Local (314) 781-2714 Fax: Parts@star-mfg.com E-mail Service@star-mfg.com Warranty@star-mfg.com www.star-mfg.com Website: Mailing Address: Star Manufacturing International Inc. 10 Sunnen Drive St. Louis, MO 63143 U.S.A... - Page 3 SPECIFICATIONS: 824M Type: Manual Valve 2 Controls, 60,000 BTUH, 573 sq. in. (3697 sq. cm) Grid Area Approximate weight: installed - 214 Lb s (97.0 kg), shipping - 244 Lbs (110.6 kg) Dimensions: 24" - Width, 32 3/8" - Depth, 18" - Height (61 cm - Width, 82.2 cm - Depth, 45.7 cm - Height) 836M Type: Manual Valve...
- Page 4 824TS Type: Snap Action Control With Safety Pilot 2 Controls, 60,000 BTUH, 573 sq. in. (3697 sq. cm) Grid Area Approximate weight: installed - 222 Lb s (100.6 kg), shipping - 250 Lbs (113.3 kg) Dimensions: 24" - Width, 32 3/8" - Depth, 18" - Height (61 cm - Width, 82.2 cm - Depth, 45.7 cm - Height) 836TS Type: Snap Action Control With Safety Pilot...
- Page 5 GENERAL INSTALLATION DATA This equipment is designed and sold for commercial use only by personnel trained and experienced in its operation and is not sold for consumer use in and around the home nor for use directly by the general public in food service locations. CAUTION Before using your new equipment, read and understand all the instructions &...
- Page 6 LEVELING UNIT This griddle is supplied with 4 feet or floor stand legs which must be screwed into the body. After the griddle is in its final position, adjust the legs to create 1/8 inch slant from back to front. This will allow the grease to run into the grease gutter and provide the proper combustion air for the burners.
- Page 7 GAS PIPING Gas piping shall be of such size and so installed as to provide a supply of gas sufficient to meet the full gas input of the appliance. If the appliance is to be connected to existing piping, it shall be checked to determine if it has adequate capacity.
-
Page 8: Pilot Flame Adjustment
PILOT FLAME ADJUSTMENT The griddles are equipped with standing pilots and should be lit immediately after the gas is turned on. MANUAL VALVE AND THROTTLING CONTROL MODELS Adjust the flame as low as possible while still providing immediate burner ignition when the control knob is turned to high. - Page 9 BURNER AIR SHUTTER ADJUSTMENT The burner air shutter has a locking screw on the bottom side of the venturi. Loosen this screw to make any adjustment and tighten the screw to lock the air shutter in place after adjustment is complete. Any adjustment must be made when the burner is at full input before the control temperature setting has been satisfied.
- Page 10 GRIDDLE CARE (NON-CHROME SURFACES) It takes very little time and effort to keep the griddle attractive and performing at top efficiency. If grease is permitted to accumulate, it will form a gummy cake and then carbonize into a hard substance which is extremely difficult to remove. To prevent this condition, the following suggestions for cleanliness should be followed: 1.
- Page 11 This limited warranty is void if it is determined by Star Manufacturing International Incorporated or one of its authorized representatives that the chrome surface has been misused or abused or subjected to the following situations: 1.
-
Page 12: Symbole De Sécurité
SYMBOLE DE SÉCURITÉ Ces symboles sont utilisés pour souligner à l’utilisateur les instructions d’utilisation ou d’entretien importantes contenues dans le manuel qui accompagne l’appareil. CONSERVEZ CE MANUEL POUR RÉFÉRENCE FUTURE AVIS L’utilisation de toute pièce autre que les pièces d’origine STAR dégage le fab- ricant de toute responsabilité. -
Page 13: Important
DONNÉES GÉNÉRALES D’INSTALLATION NOTIFICATION ATTENTION Quand cet appareil est installé avec des roulettes, il doit être installé avec les roulettes fournies, un connecteur étant conforme à la norme ANSI Ce matériel est conçu et vendu pour l’usage commercial seulement par le personnel qualifié et Z21.69 ou au CAN/CGA-6.16 et à... - Page 14 RASANT DE L'UNITÉ ATTENTION Cette plaque en fonte est fournie 4 pieds ou jambes d'éventaire d'étage qui doivent être vissées N’INSTALLEZ PAS SANS ATTACHER ES dans le corps. Après que la plaque en fonte est PIEDS OU DES JAMBES ET L'ETAGERE dans sa position finale, régler les jambes pour FOURNIES DE STAND.
- Page 15 TUYAUTERIE À GAZ GAZ PROPANE - CONVERSION La taille de la tuyauterie à gaz et la façon dont elle Cette gauffreuse est équipée des capots fixes est installée doivent être telles qu’elle fournisse d’orifice et est expédiée de l’usine pour l’usage avec une alimentation suffisante de gaz pour répondre le gaz naturel.
- Page 16 ALLUMER DES INSTRUCTIONS MODÈLES EXTÉRIEURS INSTANTANÉS Quand la gauffreuse est d’abord allumée, il fum- DE THERMOSTAT ET DE CHROME era jusqu’à ce que les huiles et les impuretés de D’CAction Ajustez le pilote tellement ap- préservatif soient consommation. Les gauffreuses proximativement 3/8 “...
- Page 17 CONNEXION ÉLECTRIQUE POUR L’CAction CUISINE Placez la molette de cadran à la configuration désirée. INSTANTANÉE ET LES MODÈLES EXTÉRIEURS DE CHROME SEULEMENT Après une période de préchauffage de 30 minutes (minimum), le gril mettra à jour automatiquement Des grils extérieurs instantanés d’action et de chrome sont équipés d’une trois-fourche fondant la température choisie.
- Page 18 Cette garantie limitée est vide si elle est déterminée par 3. Suivez les étapes 2 et 3 du soin de gril (non Star Manufacturing International Incorporated ou surfaces de chrome). un de ses représentants autorisés que la surface de chrome a été...
- Page 19 Visit our Website at: www.star-mfg.com Email: service@star-mfg.com THOROUGHLY INSPECT YOUR UNIT ON ARRIVAL This unit has been tested for proper operation before leaving our plant to insure delivery of your unit in perfect condition. However, there are instances in which the unit may be damaged in transit. In the event you discover any type of damage to your product upon receipt, you must immediately contact the transportation company who delivered the item to you and initiate your claim with same.
- Page 20 NAMEPLATE REFER TO THE PARTS LIST SPECIFIC TO YOUR MODEL FOR MORE DETAIL INFORMATION. Model: 800 SERIES STAR MANUFACTURING INTERNATIONAL, INC. SK1878 REV B 3-30-09...
-
Page 21: Parts List
PARTS LIST February 10, 2010, Rev G 824 Series MODEL Number Part Number Number Description Unit Model G5-Z4812 FLUE 824M/T/TS/TSCHS G5-824004 GRIDDLE PLATE ASSY COMPLETE 824M G5-824005 GRIDDLE PLATE ASSY COMPLETE 824T/TS G5-824006 GRIDDLE PLATE ASSY COMPLETE 824TSCHS G5-Z4793 BULB CLAMP 824T/TS/TSCHS G5-Z4794 BULB COVER... - Page 22 PARTS LIST February 10, 2010, Rev G 836 Series MODEL Number Part Model Number Number Unit Description G5-Z4813 FLUE 836M/T/TS/TSCHS G5-Z4817 FLUE DIVIDER 836M/T/TS/TSCHS G5-836004 GRIDDLE PLATE ASSY COMPLETE 836M G5-836005 GRIDDLE PLATE ASSY COMPLETE 836T/TS G5-836006 GRIDDLE PLATE ASSY COMPLETE 836TSCHS G5-Z4793 BULB CLAMP...
- Page 23 PARTS LIST February 10, 2010, Rev G 848 Series MODEL Number Part Model Number Number Description Unit G5-Z4814 FLUE 848M/T/TS/TSCHS G5-Z4817 FLUE DIVIDER 848M/T/TS/TSCHS G5-848004 GRIDDLE PLATE ASSY COMPLETE 848M G5-848005 GRIDDLE PLATE ASSY COMPLETE 848T/TS G5-848006 GRIDDLE PLATE ASSY COMPLETE 848TSCHS G5-Z4793 BULB CLAMP...
- Page 24 PARTS LIST February 10, 2010, Rev G MODEL 860 Series Number Part Description Model Number Number Unit G5-Z4815 FLUE 860M/T/TS/TSCHS G5-Z4817 FLUE DIVIDER 860M/T/TS/TSCHS G5-860004 GRIDDLE PLATE ASSY COMPLETE 860M G5-860005 GRIDDLE PLATE ASSY COMPLETE 860T/TS G5-860006 GRIDDLE PLATE ASSY COMPLETE 860TSCHS G5-Z4793 BULB CLAMP...
- Page 25 PARTS LIST February 10, 2010, Rev G 872 Series MODEL Number Part Model Number Number Unit Description G5-Z4816 FLUE 872M/T/TS/TSCHS G5-Z4817 FLUE DIVIDER 872M/T/TS/TSCHS G5-872004 GRIDDLE PLATE ASSY COMPLETE 872M G5-872005 GRIDDLE PLATE ASSY COMPLETE 872T/TS G5-824006 GRIDDLE PLATE ASSY COMPLETE 872TSCHS G5-Z4793 BULB CLAMP...
- Page 28 PARTS LIST February 10, 2010, Rev G 800M and 800T Series MODEL Number Part Description Number Number Model Unit 2K-Z4901 MANIFOLD 824M/T 2K-Z4902 MANIFOLD 836M/T 2K-Z4903 MANIFOLD 848M/T 2K-Z4904 MANIFOLD 860M/T 2K-Z4905 MANIFOLD 872M/T 2K-Z4921 BURNER FLEX TUBE 824M/T BURNER FLEX TUBE 836M/T BURNER FLEX TUBE 848M/T...
- Page 34 PARTS LIST February 10, 2010, Rev G 824TS and 824TSCHS Series MODEL Number Part Description Number Model Number Unit 2K-Z4921 824TS/TSCHS BURNER FLEX TUBE 2K-2675 824TS/TSCHS FITTING 3/8 CC X 3/8 MPT 2P-1453 824TS/TSCHS PIPE PLUG 2K-Y5550 824TS/TSCHS NIPPLE 3/8 NPT X 1 1/2 2K-2665 824TS/TSCHS ELBOW 3/8 NPT...
- Page 35 PARTS LIST February 10, 2010, Rev G 836TS and 836TSCHS Series MODEL Number Part Number Number Description Model Unit 2K-Z4921 836TS/TSCHS BURNER FLEX TUBE 2K-2675 836TS/TSCHS FITTING 3/8 CC X 3/8 MPT 2P-1453 836TS/TSCHS PIPE PLUG 2K-Y5550 836TS/TSCHS NIPPLE 3/8 NPT X 1 1/2 2K-2665 836TS/TSCHS ELBOW 3/8 NPT...
- Page 36 PARTS LIST February 10, 2010, Rev G 848TS and 848TSCHS Series MODEL Number Part Description Model Number Number Unit 2K-Z4921 848TS/TSCHS BURNER FLEX TUBE 2K-2675 848TS/TSCHS FITTING 3/8 CC X 3/8 MPT 2P-1453 848TS/TSCHS PIPE PLUG 2K-Y5550 848TS/TSCHS NIPPLE 3/8 NPT X 1 1/2 2K-2665 848TS/TSCHS ELBOW 3/8 NPT...
- Page 37 PARTS LIST February 10, 2010, Rev G 860TS and 860TSCHS Series MODEL Part Model Number Description Number Number Per Unit 2K-Z4921 860TS/TSCHS BURNER FLEX TUBE 2K-2675 860TS/TSCHS FITTING 3/8 CC X 3/8 MPT 2P-1453 860TS/TSCHS PIPE PLUG 2K-Y5550 860TS/TSCHS NIPPLE 3/8 NPT X 1 1/2 2K-2665 860TS/TSCHS ELBOW 3/8 NPT...
- Page 38 PARTS LIST February 10, 2010, Rev G 872TS and 872TSCHS Series MODEL Part Model Number Description Number Number Per Unit 2K-Z4921 872TS/TSCHS BURNER FLEX TUBE 2K-2675 872TS/TSCHS FITTING 3/8 CC X 3/8 MPT 2P-1453 872TS/TSCHS PIPE PLUG 2K-Y5550 872TS/TSCHS NIPPLE 3/8 NPT X 1 1/2 2K-2665 872TS/TSCHS ELBOW 3/8 NPT...
- Page 40 STAR INTERNATIONAL HOLDINGS INC. COMPANY Star - Holman - Lang - Wells - Bloomfield - Toastmaster 10 Sunnen Drive, St. Louis, MO 63143 U.S.A. (800) 807-9054 (314) 781-2777 Parts & Service (800) 807-9054 www.star-mfg.com...