Remote Control Unit - BIELMEIER BHG 280 Mode D'emploi

GB
3 AUtOMAtIC MODE (29)
In this mode the appliance adjusts itself accord-
ing to the air quality . The air is purified with the
power level (28) automatically selected, and the
appliance switches off as soon as the ideal purity
for room air is attained .
Appliance performance depends
on the quality of the air (20):

very good quality low performance level

good quality medium performance level

normal quality high performance level

poor quality very high performance level
Each of the four power levels (28) has a differ-
ent colour on the operation indicator (27):

low performance level green

medium performance level blue

high performance level orange

very high performance level red
4 MANUAL SEttING
Press "Auto" (36) on the remote control unit (16)
or "Gebläse" (fan) (22) on the appliance to leave
Automatic mode (29) . You can now directly se-
lect the program you require by pressing "Auf-
frischen" (refresh) (24) for ionisation or "Luft
reinigen" (purify air) (23) for photocatalytic pu-
rification, pressing neither or both buttons and
selecting the required performance level for the
appliance with "Gebläse" (fan) (22) . The setting
last selected for the appliance will be saved and
used when it is next started up .
5 SELECt OPERAtING tIME (21)
Running times from 1 to 12 hours can be selected .
An hour is set each time you press the "Dauer" (du-
ration) button (25 / 35) . The running time will start
as soon as selection ends . If you hold down the
"Dauer" (duration) button (25 / 35), this will speed
up time selection . The air purifier switches off au-
tomatically when the selected time expires .
6 AIR qUALItY INDICAtOR
There are four levels used to display the air quality
for "Staub" (dust) (20) and "Gas" (gas) (20) .
Very good, good, normal and poor (see Fig. 1) .
16

REMOtE CONtROL UNIt (4)

FUNCtIONS OF BUttONS
EIN / AUS 32
Gebläse 33
Auffrischen 34
Dauer 35
Auto 36
Luft reinigen 37
32 Appliance is switched on / off .
33 Controls fan speed .
34 Starts or stops ion generator .
35 Selects the length of time the
appliance is to remain in operation
(1 – 12 hours) .
36 Starts or stops Automatic mode .
37 Starts or stops photocatalytic
purification .
Fig. 3: Remote control (4)
INSERt BAttERIES
1 Open battery compartment on rear of remote
control unit (4) .
2 Insert batteries correctly .
When doing so, take note of "+" and "–" sym-
bols marked on the inside of the remote control
unit .
3 Now close the battery compartment again .
CLEANING AND CARE OF APPLIANCE
HOUSING
Please make sure you remove the power plug
before cleaning the appliance .
Only clean the appliance when necessary . If it
is used in a contaminated environment, it may
need to be cleaned more frequently .
Remove dirt with a soft cloth .
Only use mild cleaning products to remove dirt .
Caution: Remove the cover (5) carefully so as not
to damage the appliance .
SENSORS (15 / 16)
Remove dust from the air inlet of the sensor .
Use the vacuum cleaner to clean the air inlets of
the sensors (15 / 16) and other parts which are
not easily accessible .
PREFILtER (7)
Filters must be regularly cleaned or replaced .
the prefilter is washable (30° washing pro-
gramme without softener) although it should
not be spun! Allow the filter to dry flat .
The filter should be washed every 3 months and
replaced once a year .
MAIN FILtER (8)
It is recommended removing the dust from this
filter (8) with the vacuum cleaner every 3 months .
The filter should be replaced when purification
efficiency falls off sharply .
Filters should generally be replaced every 1 – 2
years .
GB
FILtER (7 / 8) – GENERAL INFORMAtION
When the air purifier has been in operation for
3 000 hours, the display will tell you that the pre-
filter (7) and main filter (8) need to be replaced .
After replacing the filters, press the "Gebläse"
(fan) (22) and "Auffrischen" (refresh) (24) buttons
simultaneously for 3 seconds to reset the oper-
ating hours . Please remember that whenever
these two buttons are pressed simultaneously,
the operating hours will be deleted .
If you forget to reset the operating hours after
exchanging the filters (7 / 8), you will again be
reminded to replace them at 3 500 operating
hours .
Please contact BIELMEIER Hausgeräte
GmbH to buy new filters.
UV tUBES (9)
If the "UV1" or "UV2" symbol (30) lights up,
this means that one or both UV tubes are not
working properly and must be replaced .
17