Assembly; Assembly Components; Steering Wheel Assembly - Stiga TC 102 Série Manuel D'utilisation

4. ASSEMBLY

The safety regulations to follow
are described in chap. 2. Strictly
comply with these instructions to
avoid serious risks or hazards.
For storage and transport purposes, some
components of the machine are not installed
in the factory and have to be assembled after
unpacking. Follow the instructions below.
Unpacking and completing the assembly
should be done on a flat and stable surface,
with enough space for machine handling
and its packaging, always making use of
suitable equipment. Do not use the machine
until all the indications provided in the
"ASSEMBLY" section have been carried out.

4.1 ASSEMBLY COMPONENTS

The packaging holds the components needed
for assembly as listed in the table below:
Description
1 Steering wheel
2 Dashboard cover and steering
wheel assembly parts
3 Driving seat
4 Front bumper (if fitted)
5 Bag with mounting screws etc. and in-
structions TS-TX-TH models only) (mod-
els with rear collector only)
6 Grass catcher bag supports and asso-
ciated attachments (models with rear
collector only)
7 Side dumping chute (for models with
side dumping only)
8 Cutting-means assembly side strength-
eners (if fitted).
9 Envelope containing:
- the instruction manuals and documents
- driving seat assembly screws
- side dumping chute assembly fittings
(for models with side dumping only)
- the connection screws for the battery
cables
- 2 starter keys
- 1 spare 10 A fuse
10 Mulching kit (models with side dumping
function only) (if fitted).
4.1.1 Unpacking
1. Cautiously open the packaging, paying
attention not to lose components.
2. Consult the documentation in the
box, including these instructions.
3. Remove all the unassembled
parts from the box.
4. Remove the machine from the packaging
taking the following precautions:
– move the cutting-means assembly
to its maximum height (par. 5.14) to
protect it against damage when the
machine is lifted off the base pallet;
– Lift the machine off the base pallet.
5. Move the front drive release lever to
the released position (par. 5.4).

4.2 STEERING WHEEL ASSEMBLY

• Type "I" steering wheel
1. Put the machine on a flat surface
and straighten the front wheels.
2. Using a screwdriver, remove the central cap
(fig. 3.B) from the steering wheel (fig. 3.A).
3. Fit the steering wheel (fig. 3.A) onto the
protruding shaft (fig. 3.C), rotate it so that the
spokes are facing the seat and then push
it so that the steering wheel hub couples
with the protruding end of the pin (fig. 3.D).
4. Secure the steering wheel using the screw
(fig. 3.E) and the washers (fig. 3.F) e (fig.
3.G) supplied, in the indicated sequence.
5. Tighten the screw (fig. 3.E) fully
using a socket wrench.
6. Replace the cap on the steering wheel (fig.
3.B) inserting it so that it clicks into place.
• Type "II" steering wheel
1. Put the machine on a flat surface
and straighten the front wheels.
2. Using a screwdriver, remove the central cap
(fig. 3.I) from the steering wheel (fig. 3.H).
3. Put the machine on a flat surface
and straighten the front wheels.
4. Fit the steering wheel (fig. 3.H) onto the
protruding shaft (fig. 3.J), rotate it so that the
spokes are aligned correctly, and then push
it so that the steering wheel hub couples
with the protruding end of the pin (fig. 3.K).
5. Secure the steering wheel using the screw
(fig. 3.L) and the elastic washer (fig. 3.M)
supplied, in the indicated sequence.
6. Tighten the screw (fig. 3.L) fully
using a socket wrench.
7. Replace the cap on the steering wheel
(fig. 3.I) inserting it so that it clicks into place.
EN - 7