Before First Use; Using The Mixer; Tips - Inventum Aluminous NB 800 Mode D'emploi

2 | before first use
Before you use the appliance for the first time, please do
as follows: carefully unpack the appliance and remove
all the packaging material. Keep the material (plastic
bags and cardboard) out of reach of children. check
the appliance after unpacking for any damage, possible
from transportation. Place the mixer on a flat and stable
surface. rinse all the accessories ­ glass jug, knives and
lid ­ with warm soapy water and dry them thoroughly.
Wipe the base with a damp cloth. always roll out the
cord completely.
When the mixer is in use, the ingredients will be
transported along the sides of the jug to the top and will
come down through the middle. this system guarantees
that even ice cubes will be completely crushed.
a plastic lock ring is connected at the bottom of the jug.
This ensures the jug to stand stable on a flat surface.
make sure that all the parts are dry before you use the
appliance.
• Place the mixer on a flat and stable surface as soon as
you have rolled out the cord.
Practice a few times to disassemble and assemble the
mixer without any ingredients.
• the middle of the lid has a cap which can be used as a
measuringcup and for adding ingredients. through the
opening in the lid you can gradually add ingredients.
• the base contains the motor. Because of it's size, the
housing is very stable. the four suctioncups on the
bottom of the base guarantee this stability.
• the switch regulates the speed of the mixer. the mixer
has 5 speeds and two pulse (ice crush) buttons.
­ position Off = off
­ position On = on
­ position 1= the lowest speed
­ position 2
­ position 3
­ position 4
­ position 5 = the highest speed
­ position = low speed ­ pulse
­ position = high speed ­ pulse
the controls are on the front of the mixer.
• the mixer can crush ice cubes with the two ice crush
buttons. This means that the mixer is only activated
when you push one of the Pulse buttons. As soon as you
let go of t he button the mixer will be deactivated.
Make sure that the speed settings button is on position
ON.
3 | using the mixer
Before plugging into a socket, check that the voltage in
your home corresponds with the voltage printed on the
bottom of the appliance.
1. Place the mixer on a flat, clean and dry surface.
2. make sure that the mixer is not activated.
3. place the ingredients in the jug and lock it with the
lid.
4. activate the mixer by choosing a speed setting.
Attention: Do not activate the mixer constantly, this
can cause engine problems. Do not use the mixer for
more then 1 minute continuously, wait 1 minute
before you operate it again.
5. When the mixer has finished mixing, blending or
crushing set the speed button to position Off and wait
until the knives have stopped turning, before you
remove the jug.

4 | tiPs

• When the glass jug is cracked or chipped, do not use
the mixer anymore.
this could lead to damage while using the mixer.
• to avoid splashes always place the lid on the jug.
• always add liquid ingredients before adding solid
ingredients in the mixer.
• the mixer mixes best when you do not add pieces
which are too large.
• always add a cup of liquids when you crush ice cubes.
• to add ingredients while the mixer is activated, take
the cap out of the lid and add the ingredients through
the opening.
• When the ingredients stick to the sides of the jug or
are not mixed properly, shut off the engine: wait until
the knives have stopped turning and push the
ingredients with a spatula towards the knives.
• to prevent the ingredients from being blend to small,
take into account that the mixer mixes in seconds, not
minutes!
• Working with warm ingredients can cause a build­up of
pressure in the jug and that can cause hot liquids to
escape when you take the lid of the jug. therefore
always remove the cap from the lid when you are
processing warm ingredients.
17