Télécharger Imprimer la page

Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

Telephone
Operating Instructions
Mode d'emploi (au verso)
IT-B7
Sony Corporation © 1998 Printed in China
WARNING
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
To avoid electrical shock, do not open the cabinet. Refer servicing to
qualified personnel only.
INDUSTRY CANADA NOTICE
NOTICE: The Industry Canada label identifies certified equipment. This
certification means that the equipment meets certain telecommunications
network protective, operational and safety requirements as prescribed in the
appropriate Terminal Equipment Technical Requirements document (s). The
Department does not guarantee the equipment will operate to the user's
satisfaction.
Before installing this equipment, users should ensure that it is permissible to be
connected to the facilities of the local telecommunications company. The
equipment must also be installed using an acceptable method of connection.
The customer should be aware that compliance with the above conditions may
not prevent degradation of service in some situations.
Repairs to certified equipment should be coordinated by a representative
designated by the supplier. Any repairs or alterations made by the user to this
equipment, or equipment malfunctions may give the telecommunications
company cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground
connections of the power utility, telephone lines and internal meatallic water
pipe system, if present, are connected together. This precaution may be
particularly important in rural areas.
Caution: Users should not attempt to make such connections themselves, but
should contact the appropriate electric inspection authority, or electrician, as
appropriate.
NOTICE: The Ringer Equivalence Number (REN) assigned to each terminal
device provides an indication of the maximum number of terminal allowed to be
connected to a telephone interface. The termination on an interface may consist
of any combination of devices subject only to the requirement that the sum of the
Ringer Equivalence Number of all the devices does not exceed 5.
3-864-045-41(1)
IMPORTANT INSTRUCTION TO USERS
• Your model (IT-B7) has been approved by the Industry Canada.
INFORMATION
This Class B digital apparatus complies with Canadian ICES-003.
Note
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Setting up the phone
Connect the phone
To telephone outlet
1
Connect the handset to the phone.
2
Plug one end of the telephone line cord (supplied) into the LINE jack,
and the other end into a telephone outlet.
3
Attach the telephone line cord in the groove.
Tip
If your telephone outlet is not modular, contact your telephone
service company for assistance.
Tilt the phone
If you want to tilt the phone, attach the supplied wall bracket on the upper part
of the bottom of the phone.
1
1
Align the › marks on the wall bracket with the center holes, and
insert the tabs into the center holes.
2
Push the bracket toward the phone.
Tips
• To remove the wall bracket, press the upper tabs.
• If you want to hang the phone on the wall, see "Mounting the phone on a wall".
Choose the dialing mode
For the phone to work properly, select an appropriate dialing mode (tone or
pulse).
DIAL MODE
switch
If you aren't sure of your dialing system
Make a trial call with the DIAL MODE switch set to T. If the call connects, leave
the switch as is; otherwise, set to P.
2
To LINE jack
Telephone line cord
(supplied)
Depending on your dialing system, set
the DIAL MODE switch as follows:
If your dialing system is
Tone
Pulse
P
T
D IA L M
O D E
1
Modular
2
Set the switch to
T
P

Publicité

loading

Sommaire des Matières pour Sony IT-B7

  • Page 1 3-864-045-41(1) IMPORTANT INSTRUCTION TO USERS • Your model (IT-B7) has been approved by the Industry Canada. INFORMATION This Class B digital apparatus complies with Canadian ICES-003. Note Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
  • Page 2: Making And Receiving Calls

    Speed dialing Making and receiving calls You can dial with a touch of a few keys by storing a phone number on a dialing key. You can store up to 10 speed dialing numbers. Making a call TONE Storing phone numbers RINGER LEVEL switch OF F...
  • Page 3: Mounting The Phone On A Wall

    Do not use any type of abrasive pad, scouring powder or solvent such as alcohol or benzine as they may damage the finish of the cabinet. If you have any questions or problems concerning your phone, please consult your nearest Sony dealer.
  • Page 4: Installation Du Téléphone

    Alignez les repères › de l’applique murale sur les orifices centraux, et insérez les ergots dans les orifices centraux. NOTICE IMPORTANTE POUR L’UTILISATEUR Poussez l’applique vers le téléphone. • Votre (IT-B7) a été approuvé par l’Industrie Canada. Conseils • Pour enlever l’applique murale, appuyez sur les ergots supérieurs. INFORMATIONS •...
  • Page 5: Composition Et Réception D'appels

    Composition abrégée Composition et réception d’appels Vous pouvez composer un numéro de téléphone en appuyant sur quelques Composition d’un appel touches après l’avoir mémorisé sur une touche d’appel. Vous pouvez enregistrer jusqu’à 10 numéro de composition abrégée. TONE (*) Mémorisation des numéros de téléphone Sélecteur RINGER LEVEL OF F...
  • Page 6: Fixation Du Téléphone Sur Un Mur

    N’utilisez pas de tampon abrasif, de poudre à récurer ni de solvants, comme l’alcool ou la benzine, car ils pourraient endommager la finition. Pour toute question ou tout problème au sujet de ce téléphone, faites appel à votre revendeur Sony.