Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
8
Add sand.
Choose the filter location beside a round section (never in a straight
section). The starting point should be at that location where the
skimmer and return holes, and as close as possible to the filtration
system. When installing the steel wall, it is important to do so in
a location protected from the wind or on a day without any wind.
Before uncoiling the wall, make sure the pre-punched holes for the
skimmer and pump return are at the top and facing the planned lo-
cation of your filter.
SAND
PLANKS
Begin inserting the wall into the bottom tracks in the middle of a
bottom plate. At first, the wall is kept in place with one or two stakes
and strings (or extra persons). One person uncoils the wall on a
beam or a plank, while a second person inserts it in the bottom
tracks. Do not uncoil more than 3 m (10') of wall before you install
a support bar or stake and string to reinforce the structure.
Once the wall is completely uncoiled, you may find that it is too
long or that both ends do not meet by a few centimetres. If such is
the case, adjust tracks and bottom plates until wall holes line up. If
this does not work, roll up the wall again, check measurements as
per chart 1.1, adjust tracks and plates, if applicable, and uncoil the
wall again. If the spread is too wide, measure the wall and check it
against the chart below.
Illustration 8.1
Inside of pool
BOLT
IMPORTANT! Installing the wall joint in non-compliance with the specifications dictated by the manufacturer will void the warranty.
A faulty installation will cause the wall/joint to split which could result in serious and/or fatal injuries!
CHART OF ACTUAL LENGTHS OF STEEL WALL ACCORDING TO MODEL
8x14
8x16
8x19
10x16 10x18 10x21 12x18 12x24 12x27 13x17
36' 4 3/4"
41' 10 1/2"
47' 4 3/4"
42' 5"
(11,09m)
(12,75m)
(14,42m)
(12,92m)
(14,58m)
WALL INSTALLATION
ST
TA A KES AND
STRINGS
E
NUT
Outside of pool
47' 10"
53' 5"
50' 7"
61' 7"
66' 12"
(16,25m)
(15,42m)
(18,77m)
(22,00m)
WALL
Join both ends of the wall by orienting folds outward to hide the ex-
clamation icon. (Illustration 8.1)
Note: If the wall is attached properly, you should no longer see
the exclamation icon. If you can always see the icon, you must
reverse the overlap.
Insert bolts and nuts in every hole and tighten with wrench (screw
head on water side of wall). Tape over screw heads with duck tape.
Do not use impact gun for wall
screws.
Minimum torque force of 60 inch
pounds to maximum of 85 inch pounds.
13x23 14x20
14x25 15x20 15x26 15x31 16x26 16x32 18x33 18x38
48' 11"
59' 10"
55' 3"
66' 3"
56' 6"
(19,91m)
(16,84m)
(20,19m)
(18,24m)
(17,22m) (20,55m) (23,90m)
End
SKIMMER HOLE
BOTTOM TRACK
BOTTOM PLATE
DET T A A IL 8.1
Fold
71' 2"
82' 2 "
67' 5"
78' 5"
(20,69m)
(25,06m)
PUMP RETURN
HOLE
Inside of pool
Outside of pool
Fold
18x44
86'
97'
53' 10-3/16" (x2)
(26,21m) (29,56m) (16,45m x2)
Publicité
Table des Matières
